07-21-2003, 11:16 AM
| #1 (permalink) |
| Registered Member Join Date: Oct 1998 Location: Pitts. Pa. USA
Posts: 61
|  New Setup 408 If anyone is running the following setup please let me know how it runs and any problems. This is my winter buildup. 351W to 408, AFR 185's, cam with at least .600 lift, winsor jr with holley 850. AOD with Lentech valve body, 10 inch converter and 4:10's out back. I found that few ? at the front may save a lot of problems later. Thanks,
__________________ 87 LX, 74 351W, performer plus intake, holley 750, vac sec., 78 prim. 80 sec., 50 pump: Wolverine cam 292-512, windsor heads, ported 3 angle valve, 4:10 rear, AOD, Lentech valve body w/ 10'' converter. No time slips yet! |
|      |
|
07-21-2003, 07:58 PM
| #2 (permalink) |
| Registered Member  Join Date: Nov 2001 Location: santa rosa ca.
Posts: 121
| Go w/ AFR205's or worker Vic Jr's . Think big , if you build it like a hot 302 it will run like a hot 302.
__________________ 65 fastback Keith Craft 408w 11:1cr AFR205's , Vic Jr. , 750 Speed Demon , MSD Digital 6+ , Aeromotive fuel system , Hooker Super Comp ,Headers , Art Carr roller C-4 w/ 10" converter and trans brake |
|
| |
|
07-22-2003, 09:05 AM
| #3 (permalink) |
| Registered Member  Join Date: Aug 2000 Location: Wisconsin
Posts: 877
| id even suggest box stock Vic jr's over the afr 185's....afr 185's are mostly used on 347 and such...etc etc.
__________________ '91 GT,410W,10.5 to 1 comp,Victor Jr. heads,Victor 5.8 intake,FTI cam,Crane retro fit lifters,Scorpian 1.6 RR's,Melling HV oil pump,MSD distro.,Canton oil pan,FMS flywheel,Romac balancer,FMS timing chain,Accufab 90mm TB,C&L 76mm maf, 42lbers,HD clutch,K&N air filter,Mac long tubes,Pro dumps,powerchamber,FMS 9mm wires,180 thermostat,Ford Racing gauges,5inch Tach,centerline convo pro's,nitto DR's,Pro3i lower control arms,50/50 shocks,3.55 gears,TFS HD diff. cover Next year: Tremec TKO,Spec stage 3 clutch,alum driveshaft,complete fuel system www.angelfire.com/linux/demondan |
|
| |
|
07-22-2003, 06:24 PM
| #4 (permalink) |
| Registered Member  Join Date: Jun 2002 Location: manassas, va
Posts: 186
| Demon, how does your car run. Could you give some time slips and numbers. Im very interested in your combo, similar to mine. I still need a tranny and an 8.8 posi. Mine ran a 7.50 at 101 in the eighth, babying it out of the hole, first time down the track before i broke the tranny. hehe. Any info would be greatly apprechiated
__________________ 1983 mustang, 393 cubic inch stroker small block, victor jr heads and intake, gold race 1.6 roller rockers. comp cam 304, 244@ .050. .576" hydralic retro roller cam,lunati rods. block was o-ringed,10:1 forged pistons, speed pro fit fit rings, clevite bearings,msd distributor and igniton,be cool huge radiator, black lite electric fan, march underdrive pulleys, mildon deep sump oil pan, mac 1 3.4" long tube headers, 3" dr gas x-pipe and mac exhaust,ARP bolts. car weighs 2900 lbs w/out driver, sub frames, weld wheels, mickey thompson sportsman pro 26 x 10.5 x 15's,#8 fuel line steel braided |
|
| |
|
07-22-2003, 10:18 PM
| #5 (permalink) |
| Registered Member Join Date: Aug 2000 Location: Wisconsin
Posts: 877
| id love to but its not quite done yet...just ran into oil pan trouble
__________________ '91 GT,410W,10.5 to 1 comp,Victor Jr. heads,Victor 5.8 intake,FTI cam,Crane retro fit lifters,Scorpian 1.6 RR's,Melling HV oil pump,MSD distro.,Canton oil pan,FMS flywheel,Romac balancer,FMS timing chain,Accufab 90mm TB,C&L 76mm maf, 42lbers,HD clutch,K&N air filter,Mac long tubes,Pro dumps,powerchamber,FMS 9mm wires,180 thermostat,Ford Racing gauges,5inch Tach,centerline convo pro's,nitto DR's,Pro3i lower control arms,50/50 shocks,3.55 gears,TFS HD diff. cover Next year: Tremec TKO,Spec stage 3 clutch,alum driveshaft,complete fuel system www.angelfire.com/linux/demondan |
|
| |
| Sponsored Links | |
| | |
 |
| Thread Tools | |
| Display Modes | Rate This Thread |
| |
Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Power Steering Setup for 68' | BDegs | Classic Mustangs | 0 | 09-11-2002 03:36 PM |
| Help In Getting The Most Hp From My Current Setup | 89FHPLX | Windsor Power | 7 | 08-19-2002 05:13 PM |
| Should I Run a Carb or EFI Setup? Please Help | BlackFireN2O | Windsor Power | 1 | 08-07-2002 04:16 PM |
| drag setup?? 86GT-struts,? | 429mustang | Windsor Power | 2 | 06-20-2002 02:56 PM |
| speed density setup, could this work? has anyone tried? | mikos chris | Windsor Power | 2 | 10-13-2001 03:20 AM |
Linear Mode
