Oil Pans

dherrer1 · 01-10-2001, 05:28 PM

I have a 1993 GT 5.0. I am doing a number of modifications and one is to upgrade the oil pump and oil pan. I have purchased a Moroso oil pan pant number MOR-20511 and when I received it I noticed it does not have the plug to re-install the low oil level sensor. Did I order the wrong oil pan or do I need to modify it? Has anyone crossed this bridge before? By the way, I am also installing the FMS high volume oil pump.

Rick 91GT · 01-11-2001, 01:20 PM

My Canton 7qt doesn't have the provision for the oil level sensor either. I didn't modify my pan to accept it, I pulled the bulb in the dash and clipped off the wires since I never planned on running it again, all my stock one did was leak and make a mess even after replacing the seal.

------------------
My Ride Check Out My Site 91GT, Holley SysteMAX II Kit-Heads 2.02" x 1.60",Full MAC exhaust 1-5/8" Long tubes, 2-1/2" O.R H-Pipe, 2 1/2" cat back, 12" K&N Filter, RNH PERFORMANCE Ram Air, Ron Davis Radiator, Full Suspension,3:73's, Welds, Best on new motor-12.60 @ 108, no traction 1.98

MiracleMax · 01-12-2001, 12:04 AM

Ditto on the Milodon pans, I just clipped my wires and the light never came on.

01-10-2001, 05:28 PM	#1
dherrer1 Registered Member Join Date: Jul 1999 Location: Carlsbad, CA Posts: 17	Oil Pans I have a 1993 GT 5.0. I am doing a number of modifications and one is to upgrade the oil pump and oil pan. I have purchased a Moroso oil pan pant number MOR-20511 and when I received it I noticed it does not have the plug to re-install the low oil level sensor. Did I order the wrong oil pan or do I need to modify it? Has anyone crossed this bridge before? By the way, I am also installing the FMS high volume oil pump.

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Aftermarket oil pans?	blue00gt	Modular Madness	2	07-19-2001 10:59 AM
67 Convertible Floor Pans	Gichigumi	Classic Mustangs	0	06-14-2001 04:12 PM
351 oil pans!	bigredstang	Windsor Power	4	05-28-2001 10:20 PM
79-82 Oil pans	zodszoo	Windsor Power	5	05-02-2001 06:29 PM
Floor pans?	86GT	Windsor Power	1	04-18-2001 09:24 PM

01-11-2001, 01:20 PM	#2
Rick 91GT Procharged! Join Date: May 1999 Location: Hanover, PA Posts: 1,539	My Canton 7qt doesn't have the provision for the oil level sensor either. I didn't modify my pan to accept it, I pulled the bulb in the dash and clipped off the wires since I never planned on running it again, all my stock one did was leak and make a mess even after replacing the seal. ------------------ My Ride Check Out My Site 91GT, Holley SysteMAX II Kit-Heads 2.02" x 1.60",Full MAC exhaust 1-5/8" Long tubes, 2-1/2" O.R H-Pipe, 2 1/2" cat back, 12" K&N Filter, RNH PERFORMANCE Ram Air, Ron Davis Radiator, Full Suspension,3:73's, Welds, Best on new motor-12.60 @ 108, no traction 1.98

01-12-2001, 12:04 AM	#3
MiracleMax Registered Member Join Date: Apr 1999 Location: Hayes, Va, USA Posts: 798	Ditto on the Milodon pans, I just clipped my wires and the light never came on.