Ok guys, u pick the right cam

mustangman65_79 · 12-30-2003, 10:56 AM

Here's the deal, I have a 5.0 HO out of a 89 Gt going into a '66 mustang, and it's not going to stay a fuel injected type. I'm going back to carb. I'm not doing anything to the block or heads. I just want a good roller cam for a stock block, Edlebrock performer RPM intake, holley 750 carb, full lenth headers, and a free flowing exhuast.

Is there anything to give me an old car sound, from a roller motor, without radical mods to the motor?

GhOsT6_9 · 12-30-2003, 11:50 AM

The FRPP B-303 or E-303 cam would be a good choice. Is better then the stock cam, but is very streetable with good power throughout the RPM's.

Simi Stang · 12-30-2003, 01:18 PM

If you're not doing anything to the stock heads...then you should run the stock cam. The stock cam works great with the stock heads. The stock heads don't flow enough to benefit from a B or E-303 cam. I had a friend do the same type of swap in to a mid 60s Mustang. He used a motor from a '90 5.0...ran the stock heads, block & internals with an Edelbrock high rise manifold, bigger carb with mechanical secondaries & long tube headers with Flowmaster mufflers. The thing sounded mean. Much healthier sounding and rumbled quite a bit louder than any stock '87'-93 I've heard. This thing hauled *** too. It was an auto (not sure which tranny) with a 2000 stall...and would wax a lot of newer Mustangs with way more mods.

mustangman65_79 · 12-31-2003, 02:07 PM

Well, I am going to sell that car after I get it done, so I was thinking, if it had a new cam, and sounded realy mean, that it would sell faster.

Would a B or E cam improve performace any on stock heads?

T5superduty · 12-31-2003, 08:17 PM

Ya the B-303 or E-303 are good choices, comp cams makes really good cams for the 5.0 also. The only thing I see wrong in this combo is the Carb. 750 is way too big even for my engine combo and you are all stock ? A 650 would be the most you should go.

mustangman65_79 · 01-02-2004, 01:35 AM

I already have a 750, and I'm not going to buy a new one cause I'm just selling the car down the road.

T5superduty · 01-02-2004, 01:46 AM

Just sayin your wasting gas and losing performance. Just making you aware of what is really happening with your car. I'm not trying to be a punk about it or anything if thats what you thought.

mustangman65_79 · 01-03-2004, 05:27 AM

Quote:

Originally posted by T5superduty
Just sayin your wasting gas and losing performance. Just making you aware of what is really happening with your car. I'm not trying to be a punk about it or anything if thats what you thought.

Oh no, I didn;t think u were being a punk-sorry, I reread my post and it kinda sounded that way, sorry.

I know about the situ with the carb, but they are so much money, that buying the right one would kill me right now. So I am going to run that one, till i sell it. MAybe the person who buys it can buy the right carb-lol

Tony Frank · 01-05-2004, 06:57 PM

id say go with a trick flow cam cause they are now cheaper than the E cam. little bigger than the E cam also

12-30-2003, 10:56 AM	#1 (permalink)
mustangman65_79 My poor 79 RIP Join Date: Oct 2001 Location: Suisun City, Posts: 2,316	Ok guys, u pick the right cam Here's the deal, I have a 5.0 HO out of a 89 Gt going into a '66 mustang, and it's not going to stay a fuel injected type. I'm going back to carb. I'm not doing anything to the block or heads. I just want a good roller cam for a stock block, Edlebrock performer RPM intake, holley 750 carb, full lenth headers, and a free flowing exhuast. Is there anything to give me an old car sound, from a roller motor, without radical mods to the motor? __________________ '98 Mustang Cobra Black/Black, Maganapacks, C&L, MGW shifter, K&N, Eibach springs, BBK caster/camber plates, KYB/AGX shocks, Real Y2K Cobra R wheels with Perrii P-Zero tires. '89 Bronco, rebuilt 351, and C6. My website! West Coast Domestics

12-30-2003, 11:50 AM	#2 (permalink)
GhOsT6_9 Registered Member Join Date: May 2000 Location: Ontario,Canada Posts: 233	The FRPP B-303 or E-303 cam would be a good choice. Is better then the stock cam, but is very streetable with good power throughout the RPM's. __________________ 1989 Mustang LX Notch 5.0L, T-5, 1969 351W heads, cut & welded stock plenum, F-303 cam, Mac 1 5/8 full length headers, Cat'd H-pipe, 3.73 gears, Underdrives, SSM lift bars, E-Fan, 3G Alt, Custom Chip, Autometer gauges, Weld Draglite wheels , M/T ET Street Radials Best 1/4: 13.33@101.53MPH

12-30-2003, 01:18 PM	#3 (permalink)
Simi Stang Registered Member Join Date: Aug 2002 Location: Simi Valley, CA. Posts: 769	stock cam If you're not doing anything to the stock heads...then you should run the stock cam. The stock cam works great with the stock heads. The stock heads don't flow enough to benefit from a B or E-303 cam. I had a friend do the same type of swap in to a mid 60s Mustang. He used a motor from a '90 5.0...ran the stock heads, block & internals with an Edelbrock high rise manifold, bigger carb with mechanical secondaries & long tube headers with Flowmaster mufflers. The thing sounded mean. Much healthier sounding and rumbled quite a bit louder than any stock '87'-93 I've heard. This thing hauled *** too. It was an auto (not sure which tranny) with a 2000 stall...and would wax a lot of newer Mustangs with way more mods. __________________ '90GT/ 306 w/ Edel. alum. hds. & performer manifold/ 24lb.inj./ B-303/ 1.72 rollers/ TRW frgd.pstns./ JBA hdrs./ MAC 2.5" off-road h-pipe w/ 2-chamber Flows/ Hurst short throw shftr./ Centerforce dual-friction clutch/ subframes/ reinforced torque boxes/ Crane HI-6 ignition/ Crane PS91 coil/ MSD timing retard for 150hp. NOS/ 3.73s/ Lakewood traction bars/ Auburn posi.... 1/4 mile times: on motor= 12.7 @ 108mph on nitrous= 11.6 @ 118mph

12-31-2003, 02:07 PM	#4 (permalink)
mustangman65_79 My poor 79 RIP Join Date: Oct 2001 Location: Suisun City, Posts: 2,316	Well, I am going to sell that car after I get it done, so I was thinking, if it had a new cam, and sounded realy mean, that it would sell faster. Would a B or E cam improve performace any on stock heads? __________________ '98 Mustang Cobra Black/Black, Maganapacks, C&L, MGW shifter, K&N, Eibach springs, BBK caster/camber plates, KYB/AGX shocks, Real Y2K Cobra R wheels with Perrii P-Zero tires. '89 Bronco, rebuilt 351, and C6. My website! West Coast Domestics

12-31-2003, 08:17 PM	#5 (permalink)
T5superduty Registered Member Join Date: Sep 2003 Posts: 114	Ya the B-303 or E-303 are good choices, comp cams makes really good cams for the 5.0 also. The only thing I see wrong in this combo is the Carb. 750 is way too big even for my engine combo and you are all stock ? A 650 would be the most you should go. __________________ Gt40 X heads,B-303 Cam, Cobra 1.7 Roller Rockers, Edelbrock Victor water pump, 3 Core Radiator, Edelbrock RPM "Air Gap"intake, Road Demon 625 cfm carb, Hooker Super competition Headers, offroad H pipe, T5

01-02-2004, 01:35 AM	#6 (permalink)
mustangman65_79 My poor 79 RIP Join Date: Oct 2001 Location: Suisun City, Posts: 2,316	I already have a 750, and I'm not going to buy a new one cause I'm just selling the car down the road. __________________ '98 Mustang Cobra Black/Black, Maganapacks, C&L, MGW shifter, K&N, Eibach springs, BBK caster/camber plates, KYB/AGX shocks, Real Y2K Cobra R wheels with Perrii P-Zero tires. '89 Bronco, rebuilt 351, and C6. My website! West Coast Domestics

01-02-2004, 01:46 AM	#7 (permalink)
T5superduty Registered Member Join Date: Sep 2003 Posts: 114	Just sayin your wasting gas and losing performance. Just making you aware of what is really happening with your car. I'm not trying to be a punk about it or anything if thats what you thought. __________________ Gt40 X heads,B-303 Cam, Cobra 1.7 Roller Rockers, Edelbrock Victor water pump, 3 Core Radiator, Edelbrock RPM "Air Gap"intake, Road Demon 625 cfm carb, Hooker Super competition Headers, offroad H pipe, T5

01-05-2004, 06:57 PM	#9 (permalink)
Tony Frank Registered Member Join Date: Feb 2001 Location: Brooklyn originally, but Grand Rapids now Posts: 309	id say go with a trick flow cam cause they are now cheaper than the E cam. little bigger than the E cam also __________________ Grand Valley State University Senior Accounting and Finance Major 1985 Mustang GT 19,000 ORIGINAL miles, E-303 cam, edelbrock performer RPM intake, holley 600 cfm carb, MAC headers, windage tray, 8.8 rear end with 4.10 gears, 4"cowl hood, 5lug conversion, 04 Mach1 wheels. http://www.mustangworks.com/cgi-bin/moi-display.cgi?1501

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Here is the deal with the GM guys at work	bri32z	Stang Stories	22	11-27-2001 01:34 PM
Bye guys	1980convertible	Blue Oval Lounge	9	11-14-2001 01:03 AM
You guys with 94-95 GT's	todd95GT	Windsor Power	6	09-29-2001 07:42 AM
What mod would u guys do next...?	90LxDroptop	Windsor Power	2	08-30-2001 04:54 PM

Sponsored Links