 
                    
                  
                    © Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
                    
                  
                MustangWorks.com is designed and hosted by Aero3 Media.
| 
 | |||||||
|  | 
|  | Thread Tools | Rate Thread | Display Modes | 
|  02-18-2002, 01:21 AM | #1 | 
| Registered Member Join Date: Nov 2000 Location: Maple Ridge B.C. Canada, The Best Place In The World 
					Posts: 871
				 |  Please Help!!! Car Wont Start!!! Need Help By Tomorrow Moring... i know my distributor is put back incorrectly,(yes, i realise that that was a dumb-*** thing to do, not mark it) and it wont start(the rotor got turned while it was out for the oil pump change)  what is the easiest way to get my car to start again??? (Unit5302 gave me a methd i may use if i dont have any other replys by tomorrow morning) 
				__________________ 1984 Bronco II, 36" Michelin Military Tires, 95 EFI 5.0, NP435 Tranny, NP208 Doubler, NP205 Transfer Case, Fill Size Solid Dana 44 Front End, WH Progressive Rate Rock Crawling Coils, Bronco 8.8 Rear, Skyjacker Softride Leafs, 5.13 Gears, Detroit Locker. Final Crawl Ratio Of 175:1 88 GT Best 60ft. 2.181 Best ET 14.350 Best MPH 98.01 ~WRECKED!!!!~ | 
|   |   | 
|  02-18-2002, 01:26 AM | #2 | 
| Registered Member Join Date: Apr 2001 Location: Staging lane 
					Posts: 4,337
				 |   I replied on your other post. 
				__________________ 92' LX-Big brakes, Lots and lots of suspension, GT40X heads, Ported cobra intake, stock cam, Vortech SC trim. 00' Lightning-Stock 88'CRX-13 second ego killer | 
|   |   | 
|  02-18-2002, 12:08 PM | #3 | 
| Junior Member Join Date: Mar 1999 Location: Ventura, California 
					Posts: 8,981
				 |   1) Pull #1 spark plug. 2) Wad up a kleenex and stuff into spark plug hole. 3) Crank engine by hand until kleenex pops out of spark plug hole. 4) Rotate engine by hand to align timing mark on balancer with 10 degree timing mark (it should be VERY close when the kleenex pops out) 5) Adjust (turn) distributor until #1 plug wire terminal lines up with rotor. 6) Tighten the distributor and fire it up. Take care, -Chris 
				__________________ Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local RED & WHITE! | 
|   |   | 
|  | 
| 
 | 
 | 
|  Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post | 
| Wont Start, help! 1995 GT 5.0 | Year2001Boogie | Windsor Power | 13 | 05-05-2004 09:26 PM | 
| EEC does not energize unless key turned to start | crazypete | Windsor Power | 23 | 09-20-2002 09:00 AM | 
| sometimes car turns over a lot but doesn't start | MineralGray02K | Modular Madness | 3 | 09-16-2002 10:41 PM | 
| Anyone Have Oictures Of The Passanger Side With BBK 1-5/8 Equals??? | BowTie Eater 5 Liter | Windsor Power | 6 | 02-18-2002 02:41 AM | 
| Any hints before I start tomorrow? | Chris_H | Windsor Power | 2 | 03-27-2001 11:42 PM | 
 
                    
                  