please help tps sensor

ahopkins81 · 08-29-2001, 03:04 PM

i need some help and advice with adjusting my tps sensor on my 1990 ford mustang 5.0

95mustanggt · 08-29-2001, 03:36 PM

Why do you want to adjust it? What is the voltage at? (You are OK from 0.5 to 1.0 V at idle)

I know that on my 95 TPS the screw holes had a metal sleave and you could not adjust it all that well.

Otherwise enlarge the 2 holes in the sensor ever so slightly and turn the TPS so that it increases or decreases the voltage.

While many here will say to get the voltage close as possible to 1.0 V in my car, there is no difference between .80 V and .98V. I recommend that you just make sure the voltage is between 0.5 V and 1.0 V.

Just my take

------------------
1995 Mustang GT

ahopkins81 · 08-29-2001, 03:42 PM

I need to know what the voltage should be and where to test for it. Which of the three wire colors- black, green, orange- should I test at? I have an idle problem.

avbcon12 · 08-29-2001, 08:28 PM

it must be below 1.0 volts or else the computer thinks you are driving, not idleing. use the black as your ground and the green as your positive. you must also make sure that at WOT the voltage is above 4.5 volts.
hope it helps. i too am having major idle problems!

Adam

08-29-2001, 03:04 PM	#1 (permalink)
ahopkins81 Registered Member Join Date: Aug 2001 Location: bartett , il . ,u.s. Posts: 2	please help tps sensor i need some help and advice with adjusting my tps sensor on my 1990 ford mustang 5.0

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
I got a free mass air sensor	stevstum	Windsor Power	2	05-27-2003 01:50 PM
Whats the best way to tell if your running lean or rich?	K.C. 5.0	Windsor Power	9	09-10-2001 04:04 PM
Sensor on Top of T5?	Green92LX	Windsor Power	13	07-29-2001 11:11 PM
Temp sensor question	RB92GT	Windsor Power	2	06-23-2001 01:23 PM
coolant temp sensor	HKstang	Windsor Power	3	04-14-2001 02:34 AM

08-29-2001, 03:36 PM	#2 (permalink)
95mustanggt Mustang is Parked :( Join Date: May 2000 Location: Kamloops, BC Posts: 2,874	Why do you want to adjust it? What is the voltage at? (You are OK from 0.5 to 1.0 V at idle) I know that on my 95 TPS the screw holes had a metal sleave and you could not adjust it all that well. Otherwise enlarge the 2 holes in the sensor ever so slightly and turn the TPS so that it increases or decreases the voltage. While many here will say to get the voltage close as possible to 1.0 V in my car, there is no difference between .80 V and .98V. I recommend that you just make sure the voltage is between 0.5 V and 1.0 V. Just my take ------------------ 1995 Mustang GT

08-29-2001, 03:42 PM	#3 (permalink)
ahopkins81 Registered Member Join Date: Aug 2001 Location: bartett , il . ,u.s. Posts: 2	I need to know what the voltage should be and where to test for it. Which of the three wire colors- black, green, orange- should I test at? I have an idle problem.

08-29-2001, 08:28 PM	#4 (permalink)
avbcon12 Registered Member Join Date: Jul 2001 Location: West Bloomfield, MI Posts: 391	it must be below 1.0 volts or else the computer thinks you are driving, not idleing. use the black as your ground and the green as your positive. you must also make sure that at WOT the voltage is above 4.5 volts. hope it helps. i too am having major idle problems! Adam

Sponsored Links