© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
01-03-2002, 12:16 AM | #1 |
Registered Member
Join Date: Mar 2000
Location: Boston, MA
Posts: 334
|
Rear water crossover on my intake?
I am thinking about getting a new intake for my carbed Stang this winter. The one I am considering doesn't have a rear water crossover. Will this be a problem? Is it going to make my car overheat? The Victor series intakes don't have rear water crossovers do they? The local Machine Shop said that I will be ok because "the rear crossover doesn't do much for cooling." I don't know if I belive this can anyone give me any insight? My mods are in the link in my siganture.
Steve |
01-03-2002, 06:34 AM | #2 |
Junior Member
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
|
You will be perfectly fine. The only practical purpose that water passage has is allowing access to the engine coolant for temp sensors and thermal vacuum switches.
Take care, -Chris
__________________
Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local
RED & WHITE! |
01-03-2002, 11:54 AM | #3 |
Registered Member
Join Date: Mar 2000
Location: Boston, MA
Posts: 334
|
Thanks Chris, I wasn't too sure if the Machine shop was giving me a straight answere, because he wouldn't tell me what the purpose of the crossover was. He just said you don't need it, it doesn't do much for cooling. I figured there needed to be a reason it was used on most intakes. Seeing as I don't run any vacuum switches and the temp sensor is up front I am golden.
Steve |
01-04-2002, 08:53 AM | #4 |
Registered Member
Join Date: Nov 2001
Location: germantown MD
Posts: 283
|
I have an intake without the rear crossover passage. I have a question about gaskets. Are there special gaskets for these manifolds which do not have the cutout where the passage would be. Would a regular gasket work just as well.
__________________
85 GT 4bbl roller cam 2 ch. Flowmasters, O/R H-pipe Performer intake and carb milodon water pump, FMS 9mm wires, aluminum driveshaft, king cobra clutch |
01-04-2002, 09:03 AM | #5 |
Junior Member
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
|
I have never seen one. They wouldn't be cost effective to make. The only way it could leak is if either surface was warped, in which case it would leak anyway!
Take care, -Chris
__________________
Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local
RED & WHITE! |
01-04-2002, 10:15 AM | #6 |
Registered Member
Join Date: Mar 2000
Location: Boston, MA
Posts: 334
|
I HAVE seen the gaskets that don't have cut outs for the rear water crossover. I have even seen them used on cars WITH the crossover. They are more expensive though. Chris is right, don't bother with them.
Steve |
01-04-2002, 10:19 AM | #7 |
Registered Member
Join Date: Nov 2001
Location: germantown MD
Posts: 283
|
Another question for chris
I only began to work on cars about a year ago. So I don't know these things. I have another question. I stumbled across a site today about spark plugs. It seems to me that the spark is one of the key parts of the cumbustion process. Yet I don't know how to pick the right set of plugs.
I tried to figure this one out on my own but I just got more confused. I understand how to properly set the gap. but what heat range or shape or type.
__________________
85 GT 4bbl roller cam 2 ch. Flowmasters, O/R H-pipe Performer intake and carb milodon water pump, FMS 9mm wires, aluminum driveshaft, king cobra clutch |
01-04-2002, 10:31 AM | #8 |
Registered Member
Join Date: Mar 2000
Location: Boston, MA
Posts: 334
|
Sorry, I didn't mean to sound like a jerk. Ok your right about the plugs being important. I would say that stock heat range plugs would be good for most near stock or mildly modified Stangs. You would probably be happy with an Autolite #26 plug, or equiv. If I'm not mistaken that is the right heat range and shape for a 302.
Steve |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
New Intake with NITROUS!!!???? | NOSstang08690 | Power Adders | 9 | 09-09-2003 07:05 AM |
Head and intake flow. Something to think about. :) | 5ohCOUPE | Windsor Power | 3 | 03-16-2003 08:52 AM |
4.6L Intake spacer!!!! | skz4u | Modular Madness | 18 | 01-27-2003 11:11 PM |
Problems with the stang | abesmith | Windsor Power | 12 | 01-14-2003 06:43 PM |
does gt40 intake work with sn95? | daz95gt | Windsor Power | 8 | 01-13-2001 08:20 AM |