New rear end, stock driveshaft???
 

Can I use my original stock driveshaft with the Currie 9" rear I just ordered? I didn't even think about that until about a half hour after I got off the phone ordering it! I'm pretty sure I will be able to. I've never heard about having to swap the driveshaft. TIA.

------------------
'69 Coupe with 351W
=========================
Edelbrock RPM intake, Edelbrock RPM cam, Edelbrock 750 cfm carb, Edelbrock lifters, Edelbrock double roller timing chain, Edelbrock valve springs, Accel coil, Moroso Blue-Max wires, Hedman headers, 2 1/2" pipe, glasspacks, Flex fan, Lakewood traction bars, C4, 3:1 gears, 290hp-stock heads
=========================
The Surgeon General didn't say anything about smoking your azz!!

I dont know BUT I would think you need a new one.

------------------
1988 LX 5.0 3060lbs (full Tank) 14.90@100.2 On a Gtech Drivetrain: 2.73 Stock Gears (New Gears Are in my house3.55), World Class T-5, Lakewood Bellhousing, Summit Adjustable Cluch Quadrant & Cable, Alumminum Driveshaft, Flaming River Manual Steering Rack Suspension: MAC Control Arms,Maximum Motorsports Front Grip Package, H&R Sport Spings, Bilstein Shocks
Engine: Steal Mounts, Ram air, K&N, Under Drive Pulles
Exhaust: 1 5/8 Un-Equal Length Mac Headers, X-pipe W\cats, Edelbrock cat\ba

I hope you're wrong Stang Runner! That will suck if I have to get a new driveshaft. Anyone know for sure?

------------------
'69 Coupe with 351W
=========================
Edelbrock RPM intake, Edelbrock RPM cam, Edelbrock 750 cfm carb, Edelbrock lifters, Edelbrock double roller timing chain, Edelbrock valve springs, Accel coil, Moroso Blue-Max wires, Hedman headers, 2 1/2" pipe, glasspacks, Flex fan, Lakewood traction bars, C4, 3:1 gears, 290hp-stock heads
=========================
The Surgeon General didn't say anything about smoking your azz!!

9" Currie rear with 3.70 Trac-Loc will be here in 2-3 week

anyone?

------------------
'69 Coupe with 351W
=========================
Edelbrock RPM intake, Edelbrock RPM cam, Edelbrock 750 cfm carb, Edelbrock lifters, Edelbrock double roller timing chain, Edelbrock valve springs, Accel coil, Moroso Blue-Max wires, Hedman headers, 2 1/2" pipe, glasspacks, Flex fan, Lakewood traction bars, C4, 9" Currie on order, 290hp-stock heads
=========================
The Surgeon General didn't say anything about smoking your azz!!

It depends on which yoke is on it. More then likely it will fit. If not hit the junk yards.

------------------
87 GT, 4 inch cowl hood,17x9 Cobra R's/255/45's,GT-40 heads,Crane 2031, Edelbrock intake, long tubes headers,h-pipe,Flows,BBK cold air, Mass air,70mm MAF, 1.7's, 1" spacer,underdrive pulleys,Pro 5.0, King Cobra, Adj. fuel Reg., Lakewood Lift Bars,50/50's,subframes, 4.10's.
Best time 12.759
Best MPH 106.79
Best 60' 1.695

Visit my site at:
http://www.geocities.com/cobrar93_2000/MyPage.html

I have an 8" rear right now. And it's a 9" Currie that I ordered. So the yoke's probably different.

And that's the bad thing, the 1 junkyard in my town has crap for Mustangs. I think they have a couple 65 or 66s. They do have a few Cougars though, not sure on the years of them.

So does anyone know for sure what I'm gonna have to do here?

------------------
'69 Coupe with 351W
=========================
Edelbrock RPM intake, Edelbrock RPM cam, Edelbrock 750 cfm carb, Edelbrock lifters, Edelbrock double roller timing chain, Edelbrock valve springs, Accel coil, Moroso Blue-Max wires, Hedman headers, 2 1/2" pipe, glasspacks, Flex fan, Lakewood traction bars, C4, 9" Currie on order, 290hp-stock heads
=========================
The Surgeon General didn't say anything about smoking your azz!!