A question for 94-95 cobras with strut towers

SlowStang2 · 08-23-2001, 07:36 PM

I had to take off my stock strut tower because the cobra intake sits higher than the stock one. What brand tower brace will clear this intake? I heard Steeda's will. Can I use the stock holes from the stock brace to bolt in the new tower brace?

------------------
94' Stang GT Convertible --Cobra upper&lower, GT-40Y Turbo Swirl aluminum heads, Mac cold air w/K&N, BBK equal length shorties, BBK offroad H-pipe, American Thunder cat-back, BBK T/B 65mm, 24lb injectors, Pro-77mm MAM, pulleys, aluminum driveshaft, 3.55s, Steeda Tri-Ax shifter, adjustable fuel regulator 14.4@100 MPH on G-tech;96 at track. (Sad, i know. This is with the stock heads)

SVT2TOP · 08-23-2001, 09:16 PM

My Steeda strut tower brace fits fine on my Cobra. I have the stock Cobra manifold.

------------------
1995 Cobra convertible 2 Top #621 of 1,003. #184 of 499. Too many mods to list

PureStreet · 08-24-2001, 10:29 AM

The Kenny Brown fit fine on my old Cobra.

moosejaw · 08-25-2001, 09:58 AM

For a raised intake the Maximum Motorsports strut tower brace is piece to get. It does not cross the intake anywhere. You could remove the intake with the brace in place.

Mike

------------------
Live near St.Louis?
Check out Mustang Muscle and Dyno in High Ridge, MO
Check out my ride.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Strut to spindle Question	Cannon	Corner Carvers Delight	3	12-23-2002 10:21 PM
simple question	Lonzo	Classic Mustangs	3	09-10-2002 09:37 AM
To strut tower or not to strut tower?	mysweetlx	Stang Stories	9	05-06-2002 12:10 PM
Strut question	sfedenia	Corner Carvers Delight	2	05-24-2001 03:27 PM
Newby here, I have a question on Odometers	mustangmama	Blue Oval Lounge	3	03-03-2001 06:43 AM

08-23-2001, 07:36 PM	#1
SlowStang2 Registered Member Join Date: May 2001 Location: Stuart, FL, US Posts: 147	A question for 94-95 cobras with strut towers I had to take off my stock strut tower because the cobra intake sits higher than the stock one. What brand tower brace will clear this intake? I heard Steeda's will. Can I use the stock holes from the stock brace to bolt in the new tower brace? ------------------ 94' Stang GT Convertible --Cobra upper&lower, GT-40Y Turbo Swirl aluminum heads, Mac cold air w/K&N, BBK equal length shorties, BBK offroad H-pipe, American Thunder cat-back, BBK T/B 65mm, 24lb injectors, Pro-77mm MAM, pulleys, aluminum driveshaft, 3.55s, Steeda Tri-Ax shifter, adjustable fuel regulator 14.4@100 MPH on G-tech;96 at track. (Sad, i know. This is with the stock heads)

08-23-2001, 09:16 PM	#2
SVT2TOP Registered Member Join Date: Aug 2001 Location: Buffalo, Ohio USA Posts: 1	My Steeda strut tower brace fits fine on my Cobra. I have the stock Cobra manifold. ------------------ 1995 Cobra convertible 2 Top #621 of 1,003. #184 of 499. Too many mods to list

08-24-2001, 10:29 AM	#3
PureStreet Registered Member Join Date: Apr 1999 Location: Ashburn, VA US Posts: 294	The Kenny Brown fit fine on my old Cobra.

08-25-2001, 09:58 AM	#4
moosejaw Registered Member Join Date: Apr 1999 Location: St.Louis,MO Posts: 274	For a raised intake the Maximum Motorsports strut tower brace is piece to get. It does not cross the intake anywhere. You could remove the intake with the brace in place. Mike ------------------ Live near St.Louis? Check out Mustang Muscle and Dyno in High Ridge, MO Check out my ride.