![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: May 2000
Location: Waterbury, Ct. USA
Posts: 4
|
![]() I need to replace the rear upper control arms on my '87 lx. I'm going to replace the lowers just because if I'm going to fight with the uppers, I might as well do both sets! My question is does anyone have experience with the Hotchkis Performance set up? These are the arms I'm thinking about. Ford Motorsport? How are these? Any replies would be helpful. Thanks...
|
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Jun 1999
Location: Walker, MI, USA
Posts: 1,202
|
![]() They all are much better than the stock ones. I could tell a diffance with them no more wheel hop. Good luck!
------------------ 1988 LX 5.0 Was 3060lbs (full Tank) 14.65@101.3 On a Gtech Drivetrain: 3.55, World Class T-5, Lakewood Bellhousing, Adjustable Cluch Cable, AL Driveshaft, Manual Steering Rack Suspension: MAC Control Arms,Maximum Motorsports Front Grip Package, H&R Sport Spings, Bilstein Shocks Engine: Steal Mounts, K&N, Under Drive Pulles Exhaust: 1 5/8 Un-Equal Length Mac Headers, X-pipe W\cats, Edelbrock cat\back Cooling:3 Core Radiator, |
![]() |
![]() |
![]() |
#3 |
Dirk Diggler
Join Date: Feb 1999
Location: SLOATSBURG, NY
Posts: 1,931
|
![]() those are good but expensive..get the MAC or Factory Five..best bang for the buck..
------------------ 1987 black notch(ex 4 banger) DSS 306 w/ main support...Elderbrock 6028 heads..gt-40 intake..24# injectors...70 mm tb..77 pro-m...accel 300+..mac full legnth..tremec w/ pro5oh...full MAC exhaust,off road h-pipe,long tubes, catback...ron davis radiator..subframes, control arms...CFDF II..o yea holley FPR sucks..dont buy one.. AIM=onesillynotch ![]() |
![]() |
![]() |
![]() |
#4 |
Don Corlione
Join Date: Jun 2001
Location: Omaha NE USA
Posts: 491
|
![]() If money is not a concern, look into the HPMotorsport Mega-bite stuff. They actually relocate some of the rearend geometry for better traction. I love mine. I noticed a huge difference after mine were installed.
------------------ Eric - 89 Mustang LX coupe 302 - Cobra Intake - GT40p heads - TFS stage 1 cam - FRPP 1.6 roller rockers - Naturally Aspirated 3:73 gears - KYB shocks and struts - Eibach springs - HPM Mega-bite Jr lower control arms - HPM upper control arms |
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: Jul 2001
Location: Houston
Posts: 10
|
![]() Hotchkis are loud and stiff. They're greasable, but that's for a reason. They need it all the time. They get real squeaky. They are also a pretty hard ride. Beat me up more than my South Sides. I've got Mac's now. Good stuff!
[This message has been edited by mustangtim (edited 07-13-2001).] |
![]() |
![]() |
![]() |
#6 |
Registered Member
Join Date: Jul 2001
Location: Homestead Pa USA
Posts: 21
|
![]() I WOULDN'T TIE UP A LOT OF MONEY ON THE UPPER ARMS.UNLIKE THE THE LOWER ARMS,WHICH ARE BEING PUSHED UPON WHEN LAUNCHING,THE UPPERS ARE BEING PULLED ON.THEY DON'T SEE THE DEFLECTION AS THE LOWERS DO(STOCK ARMS).PLUS,THEY HAVE SMALLER DIAMETER BUSHINGS,WHICH HAVE LESS MOVEMENT,UNLIKE THE BIG SQUISHY BUSHINGS OF STOCK LOWERS.
|
![]() |
![]() |
![]() |
#7 |
Registered Member
Join Date: Apr 2001
Location: Mansfield, OH.
Posts: 113
|
![]() I welded 10 ga. steel to box my uppers. Added urethane bushings to upper and stock lower arms. Coated them with Amsoil water resistant grease so they would not sweak. I do solo 2 racing and this really firmed up rear end and goes thru corners a lot better than with stock set up. The best part is it only cost $70 big ones. Try this if your not putting a lot horse power to the rear wheels. Hope I was of some help.
------------------ Independent Amsoil dealer. For needs or information about amsoil synthetic products leave a message. Ask about preffered customer program. |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Control Arms?Does anyone have any recommendations on rear control arms? Do I really n | schizcat | Windsor Power | 5 | 08-28-2003 09:53 PM |
Rear Control Arms | Mac_5.0 | Windsor Power | 3 | 04-16-2003 08:25 AM |
Rear lower control arms | explicitone | Windsor Power | 5 | 04-24-2002 11:49 AM |
REAR UPPER AND LOWER CONTROL ARMS | bcinyuz | Windsor Power | 1 | 05-08-2001 04:17 AM |
Rear upper control arms | red82gt | Corner Carvers Delight | 2 | 08-01-2000 11:10 AM |