Timing ???? one quick ?

geno5.0 · 03-14-2002, 11:52 AM

I have a new timing light and was going to adjust my timing is there a vac advance that I need to pull off or somthing ????

geno5.0 · 03-14-2002, 01:49 PM

Its a 91 gt 5.0 help!!!!!!!!!!!!!!

vande97 · 03-14-2002, 02:09 PM

you need to remove the spout connector , before setting the timing. you can find it along the wire harness that is connected to the Distributor, it looks like a little plug , just pull it out set the timming (INT) and then replace after you are all said and done...

hope this helps

geno5.0 · 03-14-2002, 02:35 PM

Thanks

03-14-2002, 11:52 AM	#1
geno5.0 Registered Member Join Date: Feb 2002 Location: Omaha Posts: 124	Timing ???? one quick ? I have a new timing light and was going to adjust my timing is there a vac advance that I need to pull off or somthing ???? __________________ Mods:Svo Alu Y Heads,1.72roller rockers,Cam,Cobra Upper&lower,bbkEqu hedders,Offroad H,FlowmasterMuffs,BBk70mm Tb,and73mmMAF,UnderDrive Pulleys,24lb Svo Inj,Kirban AFPR,190lph Walbro,Griffin Alu Rad,Crane Coil,Batt Relocated to trunk,K/Ncone,smog pump removed,Built Aod,DSSL,3.73gears,Alu flywheel,2800stall,NOS 5115 100shot, Iknow I forgot something Best on motor13.66@102.55 2.14 60' Best on spray13.20@108.98(2.69 60') I Bet mid to low 12 if I can Hook! All runs on street tires

03-14-2002, 01:49 PM	#2
geno5.0 Registered Member Join Date: Feb 2002 Location: Omaha Posts: 124	please Its a 91 gt 5.0 help!!!!!!!!!!!!!! __________________ Mods:Svo Alu Y Heads,1.72roller rockers,Cam,Cobra Upper&lower,bbkEqu hedders,Offroad H,FlowmasterMuffs,BBk70mm Tb,and73mmMAF,UnderDrive Pulleys,24lb Svo Inj,Kirban AFPR,190lph Walbro,Griffin Alu Rad,Crane Coil,Batt Relocated to trunk,K/Ncone,smog pump removed,Built Aod,DSSL,3.73gears,Alu flywheel,2800stall,NOS 5115 100shot, Iknow I forgot something Best on motor13.66@102.55 2.14 60' Best on spray13.20@108.98(2.69 60') I Bet mid to low 12 if I can Hook! All runs on street tires

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Total timing vs initial timing for max HP.	Dark_5.0	Windsor Power	35	04-28-2009 11:35 PM
Check engine light after steeda pullies / timing adjuster!! HELP!!	MineralGray02K	Modular Madness	1	09-29-2002 01:11 AM
Should I Retard My Timing??? (Quick, But Important, Please Reply Soon)	BowTie Eater 5 Liter	Windsor Power	3	02-20-2002 12:51 PM
points and timing specs	xfernal	Classic Mustangs	1	12-30-2001 04:20 PM
timing chain or timing gear	mustang66teen	Classic Mustangs	11	06-18-2001 08:44 PM

03-14-2002, 02:09 PM	#3
vande97 Registered Member Join Date: Jan 2001 Location: okemos Posts: 205	you need to remove the spout connector , before setting the timing. you can find it along the wire harness that is connected to the Distributor, it looks like a little plug , just pull it out set the timming (INT) and then replace after you are all said and done... hope this helps