AFR 185's = 347 Stroker

fastang · 05-09-2001, 03:36 PM

Is anyone using this combo? The info on AFR's site says that they are for 351's. The displacement isnt that much different. Will they work well?

------------------
95GT B303 cam, 1.7 rockers, 65mm TB, 73mm MAF, milled heads, 355's K&N, BBK Longtubes, Flowmaster cat back, pulleys, msd coil, 9mm wires, Tremec 3550, Pro5.0 shifter,10.5 Motorsport clutch, FMS aluminum driveshaft, weld in subframe connectors

84_GT350 · 05-09-2001, 03:51 PM

I think they'd work very well...better than a pair of 165s just so long as you have a cam and intake setup that will allow you to flow the air and fuel required to make those heads scream. And remember, stroker engines are much more forgiving of cams than smaller engines. Don't be afraid to pick one that would seem big for a 302.

------------------
1984 1/2 GT350 (#842 Hatchback w/ T-tops), 302HO, Comp cams Xtreme Energy cam, Carter 625cfm carb, Weiand Stealth intake, MSD distributor, MSD coil, FMS 9mm wires, 1 5/8" MAC unequal shorties, 2 1/2" MAC Prochamber H-pipe, Flowmaster 2 chambers, KYBs, 16"x8" 4 lug Cobra Rs, Falken 245/45ZR16s

fastang · 05-09-2001, 06:32 PM

Well, currently I have 514 lift with 224 duration. Its a little much for my stock heads. It would probably feed my stroker but I was going to go bigger, what do you think?

------------------
95GT B303 cam, 1.7 rockers, 65mm TB, 73mm MAF, milled heads, 355's K&N, BBK Longtubes, Flowmaster cat back, pulleys, msd coil, 9mm wires, Tremec 3550, Pro5.0 shifter,10.5 Motorsport clutch, FMS aluminum driveshaft, weld in subframe connectors

TheSloAod · 05-09-2001, 09:21 PM

in a couple of weeks i can tell you how they work on a 10.5:1 306. I bought the stage 2 185s, my cam lift is 612 though

fastang · 05-12-2001, 05:09 PM

The wesbite said not to go over 5.50 lift. Maybe Im wrong but I wouldt want you to screw your motor up. Better check your clearance well. I called them and they said that they would work extremely well on a 347.

------------------
95GT B303 cam, 1.7 rockers, 65mm TB, 73mm MAF, milled heads, 355's K&N, BBK Longtubes, Flowmaster cat back, pulleys, msd coil, 9mm wires, Tremec 3550, Pro5.0 shifter,10.5 Motorsport clutch, FMS aluminum driveshaft, weld in subframe connectors

05-09-2001, 03:36 PM	#1
fastang Registered Member Join Date: Aug 2000 Location: santa ana ca Posts: 1,349	AFR 185's = 347 Stroker Is anyone using this combo? The info on AFR's site says that they are for 351's. The displacement isnt that much different. Will they work well? ------------------ 95GT B303 cam, 1.7 rockers, 65mm TB, 73mm MAF, milled heads, 355's K&N, BBK Longtubes, Flowmaster cat back, pulleys, msd coil, 9mm wires, Tremec 3550, Pro5.0 shifter,10.5 Motorsport clutch, FMS aluminum driveshaft, weld in subframe connectors

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Blown Stroker Computer Help	RabidPony	Modular Madness	10	02-07-2004 11:56 PM
'super' stroker vs 'budget' stroker	mike5p01	Windsor Power	4	10-11-2003 10:11 PM
351w or 347 stroker? which is better?	BLACK85GT	Windsor Power	55	12-21-2002 06:52 PM
Decided to build a stroker, but where do I start?	WhiteLX	Windsor Power	5	12-16-2002 10:35 AM
stroker engine question	82 GT	Windsor Power	1	06-08-2001 03:22 PM

05-09-2001, 03:51 PM	#2
84_GT350 Registered Member Join Date: Apr 1999 Location: Overland Park, KS, USA Posts: 1,631	I think they'd work very well...better than a pair of 165s just so long as you have a cam and intake setup that will allow you to flow the air and fuel required to make those heads scream. And remember, stroker engines are much more forgiving of cams than smaller engines. Don't be afraid to pick one that would seem big for a 302. ------------------ 1984 1/2 GT350 (#842 Hatchback w/ T-tops), 302HO, Comp cams Xtreme Energy cam, Carter 625cfm carb, Weiand Stealth intake, MSD distributor, MSD coil, FMS 9mm wires, 1 5/8" MAC unequal shorties, 2 1/2" MAC Prochamber H-pipe, Flowmaster 2 chambers, KYBs, 16"x8" 4 lug Cobra Rs, Falken 245/45ZR16s

05-09-2001, 06:32 PM	#3
fastang Registered Member Join Date: Aug 2000 Location: santa ana ca Posts: 1,349	Well, currently I have 514 lift with 224 duration. Its a little much for my stock heads. It would probably feed my stroker but I was going to go bigger, what do you think? ------------------ 95GT B303 cam, 1.7 rockers, 65mm TB, 73mm MAF, milled heads, 355's K&N, BBK Longtubes, Flowmaster cat back, pulleys, msd coil, 9mm wires, Tremec 3550, Pro5.0 shifter,10.5 Motorsport clutch, FMS aluminum driveshaft, weld in subframe connectors

05-09-2001, 09:21 PM	#4
TheSloAod Registered Member Join Date: Apr 2001 Location: baytown, tx usa Posts: 121	in a couple of weeks i can tell you how they work on a 10.5:1 306. I bought the stage 2 185s, my cam lift is 612 though

05-12-2001, 05:09 PM	#5
fastang Registered Member Join Date: Aug 2000 Location: santa ana ca Posts: 1,349	The wesbite said not to go over 5.50 lift. Maybe Im wrong but I wouldt want you to screw your motor up. Better check your clearance well. I called them and they said that they would work extremely well on a 347. ------------------ 95GT B303 cam, 1.7 rockers, 65mm TB, 73mm MAF, milled heads, 355's K&N, BBK Longtubes, Flowmaster cat back, pulleys, msd coil, 9mm wires, Tremec 3550, Pro5.0 shifter,10.5 Motorsport clutch, FMS aluminum driveshaft, weld in subframe connectors