Hybrid Mode
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
|
|
05-02-2001, 11:41 AM
|
#1 |
|
Dirk Diggler
Join Date: Feb 1999
Location: SLOATSBURG, NY
Posts: 1,931
|
94 bronco 351 q's
i can get one of these for $200 this friday..i got a few questions first..
1-are the pistons forged? 2-whats the compression ratio with stock cc heads? 3-is it a 4 bolt or 2 bolt? 4-what is the HP rating on one of these 5-scence is it a roller motor can i use 5.0 roller cams in it? 6-what carb,cam, and intake do you guys recremend for this car to look upward of 400-450 HP N/A ------------------ 1987 black notch(ex 4 banger) DSS 306 w/ main support...Elderbrock 6028 heads..gt-40 intake..24# injectors...70 mm tb..77 pro-m...accel 300+..mac full legnth..tremec w/ pro5oh...full MAC exhaust,off road h-pipe,long tubes, catback...ron davis radiator..subframes, control arms...CFDF II..o yea holley FPR sucks..dont buy one.. AIM=onesillynotch |
|
|
|
05-02-2001, 02:45 PM
|
#2 |
|
Registered Member
Join Date: Jan 2001
Location: ny
Posts: 197
|
if you want i can build you a nice motor with that 351. the compression is in the 8's and theyre not forged pistons. but since you want n/a you are better off. the stock heads arent that good but some port work would help. a torker intake with 700 holley dp and a good cam will make it run good. i like solid rollers but if you want to use hyd. then thats fine.the cams are the same but dont use a motorsport cam.
|
|
|
|
|
05-02-2001, 03:09 PM
|
#3 |
|
Dirk Diggler
Join Date: Feb 1999
Location: SLOATSBURG, NY
Posts: 1,931
|
thanks juiceman..my buddy said he talked to you online about the motor allready..i think we will just put better pitons in it and change the bearings..the motor i would like to spray eventually..yes i would not use a motorsport cam..i was thinkg a custom or a comp cams XE series cam
------------------ 1987 black notch(ex 4 banger) DSS 306 w/ main support...Elderbrock 6028 heads..gt-40 intake..24# injectors...70 mm tb..77 pro-m...accel 300+..mac full legnth..tremec w/ pro5oh...full MAC exhaust,off road h-pipe,long tubes, catback...ron davis radiator..subframes, control arms...CFDF II..o yea holley FPR sucks..dont buy one.. AIM=onesillynotch |
|
|
|
|
05-03-2001, 02:41 PM
|
#4 |
|
Dirk Diggler
Join Date: Feb 1999
Location: SLOATSBURG, NY
Posts: 1,931
|
well were def ganna spray it now so what compression and pistons do you recremend
------------------ 1987 black notch(ex 4 banger) DSS 306 w/ main support...Elderbrock 6028 heads..gt-40 intake..24# injectors...70 mm tb..77 pro-m...accel 300+..mac full legnth..tremec w/ pro5oh...full MAC exhaust,off road h-pipe,long tubes, catback...ron davis radiator..subframes, control arms...CFDF II..o yea holley FPR sucks..dont buy one.. AIM=onesillynotch |
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| '94 Ford Bronco | Simi Stang | Built Ford Tough | 9 | 01-14-2005 12:35 AM |
| '76 302 Bronco engine questions | QuantumMotorsports | Windsor Power | 1 | 05-05-2003 12:32 AM |
| '94 Ford Bronco starting problems | Simi Stang | Built Ford Tough | 5 | 01-17-2003 08:53 PM |
| 80' Bronco | NewAge 5.0 | Built Ford Tough | 4 | 11-27-2002 12:45 PM |
| Daily driven '83 Bronco 4x4 needs more power | Nitrous Al | Built Ford Tough | 5 | 03-06-2001 03:10 AM |