![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Apr 2002
Location: racine ,wi
Posts: 691
|
![]() I just picked up the frpp adj. timing chain set . what do you guys think the best setting would be for stock cam and head combo.
THANX FOR ANY HELP
__________________
RUN IT STAIGHT AND RUN IT HARD ________ Novi 2000 60' 1.46 1/4 10.67 mph 126.5 _________ |
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Sep 2000
Location: Lafayette, Indiana
Posts: 120
|
![]() straight up
__________________
89 GT convertible, Kenny Brown level 5, Edelbrock performer, AFR 165's, Comp cams XE270HR, C&L 76, 24# inj, Crane 1.7's, 70mm BBK throttle body 298.2 hp 328.2 tq Mustang dyno "Our lady of blessed acceleration don't fail me now" Elwood Blues |
![]() |
![]() |
![]() |
#3 |
Junior Member
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
|
![]() Agreed.
Take care, -Chris
__________________
Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local
RED & WHITE! |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Apr 2002
Location: racine ,wi
Posts: 691
|
![]() thanks guys
__________________
RUN IT STAIGHT AND RUN IT HARD ________ Novi 2000 60' 1.46 1/4 10.67 mph 126.5 _________ |
![]() |
![]() |
![]() |
#5 |
motors done......woohooo
Join Date: Mar 2002
Posts: 799
|
![]() i had a question that kind of went along with his so i didnt want to post another question.... my question is basically the same except i have an e303 cam, roller rockers, edelbrock rpm heads, edelbrock rpm intake, mass air, throttlebody, cold air kit, 3.73, bored .030 over, long tubes, h pipe, 21/2 tailpipes, should i leave my timing straight up too, i have heard that advancing the cam or retarding it will make you have more low or upper rpm torque and power, i am looking for lots of low end torque. THANKS FOR YOUR INFO
|
![]() |
![]() |
![]() |
#6 |
Junior Member
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
|
![]() Generally speaking, advancing the valve timing (cam) brings the powerband into full effect at a lower rpm, and retarding the valve timing raises the rpms at which the powerband will peak.
The best way to find your optimum valve timing is to install a compression gauge in one of the cylinders after bolting down the timing chain, and crank the engine over 6 or 7 times, and write down the compression. Next, back off the cam gear, and change the valve timing, then check the compression again. Keep doing this until you reach the highest compression level, and this will be the best spot for your cam. Don't forget, just like any other time you do a compression test, to block the throttle open. Take care, -Chris
__________________
Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local
RED & WHITE! |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Total timing vs initial timing for max HP. | Dark_5.0 | Windsor Power | 35 | 04-28-2009 11:35 PM |
Check engine light after steeda pullies / timing adjuster!! HELP!! | MineralGray02K | Modular Madness | 1 | 09-29-2002 01:11 AM |
points and timing specs | xfernal | Classic Mustangs | 1 | 12-30-2001 04:20 PM |
timing chain or timing gear | mustang66teen | Classic Mustangs | 11 | 06-18-2001 08:44 PM |
nos & timing controller | todd5litre | Windsor Power | 5 | 01-09-2001 08:24 PM |