![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Guest
Posts: n/a
|
![]() Pulled my motor, rebuild in progress, the remaining decision, rear end gears....
I read an article that stated with a 5 speed and 4:10's my motor should run at about 2200 RPM's at 65 MPH... if this # is correct, that's seems ok for street use, a bit high, but not bad (and the launch should be awesome, if I can get the traction, currently running 50's on the rear) my question for the guys running, 4:10's or 3:73's.. is this RPM # correct??? or should I opt for the 3:73's.... Input please..... thx in advance... ------------------ Black, 84 GT, ground effects, shorty headers, dual exh., rear spoiler from a 87, just getting started... |
![]() |
![]() |
#2 |
Procharged!
Join Date: May 1999
Location: Hanover, PA
Posts: 1,539
|
![]() Go with the 4:10's if you plan on staying NA, if a blower is in the near future get 3:73's. The 4:10's will be fine on the street and with a 5spd, I only turn around 1700-1800 in 5th gear with my 3:73's at 65-70mph. I am going with 4:30 gears which will suit my combo, run around 2300-2400 at 65mph I think around 6300 through the traps.
Good Luck on the new combo ![]() ------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC exhaust 1-5/8" Long tubes,2-1/2" O.R H-Pipe,2 1/2" cat back, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension,S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! |
![]() |
![]() |
![]() |
#3 |
Guest
Posts: n/a
|
![]() thx Rick, I was hopin the article was correct....
|
![]() |
![]() |
#4 |
Procharged!
Join Date: May 1999
Location: Hanover, PA
Posts: 1,539
|
![]() Forgot to tell you those were with 26" tall tires, a low profile tire will make it run like it has taller gears (EXAMPLE- 3:73s feel like 4:10's with 24" tires) a taller tires calms the taller gears down.
|
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: May 2001
Location: Casselberry, FL USA
Posts: 28
|
![]() Are you guys serious? My rear end gearing is 4.08 stock on my 240sx, and I thought that your Mustang's must've been using a different scale, because a Mustang stock is 2.8x or something I believe. At 70mph in 5th gear, I'm at 3k rpm. I'm fine with that, it's not a problem. So it sounds like 4.10 would be good (streetable) in a Mustang? And what effect would a blower create? Thanks.
|
![]() |
![]() |
![]() |
#6 |
Sober voice of Reason
Join Date: Nov 1998
Location: Kelowna, B.C., Canada
Posts: 1,514
|
![]() Remember, a 240 sx has half as much torque as a mustang, not to mention that the transmission ratios are different, basically its apples to oranges.
jerryIII, if I didn't do a lot of highway driving I'd probably have 410's or 430's with my combo. ------------------ GT-40 heads (ported, polished, + milled), B303 cam, 1.7rr's, JE pistons, Offy intake, Carter AFB 625cfm carb, Flowtech 1 5/8" shortys, Flowtech X-pipe, MAC Flowpath exhaust, MAC pulleys, 373's, subframes, Eibachs+Tokicos, B&M ripper, FMS Clutch, Zoom Quadrant+cable, 17" CSA Ultra rims, 235/45ZR17 Yokohama AVS S4's, MSD 6A ignition+coil, FMS 9mm wires, Carbed, Naturally Aspirated, and Nasty! |
![]() |
![]() |
![]() |
#7 |
Guest
Posts: n/a
|
![]() Red, my drive is 35 miles one way, 50% highway, i was'nt sure 4:10's would work, but after the replies and some additional conversation with other Mustang people, i will be happy.... Just not sure what i'll do after i get used to the new gearing....
NOS perhaps???? ------------------ Black, 84 GT, ground effects, shorty headers, dual exh., rear spoiler from a 87, just getting started... |
![]() |
![]() |
#8 |
Sober voice of Reason
Join Date: Nov 1998
Location: Kelowna, B.C., Canada
Posts: 1,514
|
![]() You'll be happy with the 410's. Truth be told, I bought my 8.8 rear fitted with a torsen diff and Richmond 373's for a price I couildn't afford to pass up so that's why I have the 373's.
|
![]() |
![]() |
![]() |
#9 |
Registered Member
Join Date: May 2001
Location: Elgin, IL, 60120
Posts: 14
|
![]() So far the general consensus I've seen is that autos do well with 4.10's and manuals do well with 3.73. Is this right?
------------------ K-9 No 'Stang just yet, but looking. |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
gears? | Spyder1914 | Small Ponies | 4 | 01-08-2003 02:23 PM |
Gears Gears Gears!!!! | COBRAon18s | Modular Madness | 20 | 05-13-2002 04:44 PM |
how can you tell what size gears you have? | Kamaro Killer | Windsor Power | 7 | 04-03-2002 02:55 PM |
Gears, need help!!!! | Edgar Negron | Windsor Power | 3 | 05-27-2001 03:10 PM |
Gears Gears Gears | Skyman | Windsor Power | 6 | 03-11-2001 11:39 PM |