![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
College Stanger
Join Date: May 1999
Location: Aiken,south carolina, usa
Posts: 1,097
|
![]() On my 1994 stock Mass airflow sensor it has a screen covering the whole. What is the screen for. Is it important or if I remove it will I gain power. I see that after markets do not seem to have the screen. Also can you do anything to the stock one like boring it to allow more air in?
__________________
2003 Sonic Blue Cobra |
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: May 2000
Location: Kamloops, BC
Posts: 2,875
|
![]() It is to prevent foreign material from entering the engine. I would leave it in place.
|
![]() |
![]() |
![]() |
#3 |
Moderator
Join Date: Dec 1999
Location: Livonia, MI, USA
Posts: 1,194
|
![]() You cannot remove it without it affecting the actual metering of the air (throws calibration off). Nor can you bore it out, without re-flowing and recalibrating it.
__________________
Darius Rudis, Moderator Corner Carvers Delight 1989 Mustang LX - Open Track Car http://www.dariusrudis.com |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Mar 1999
Location: Jackson, LA
Posts: 264
|
![]() i also read that it straightens the airflow out and eliminates turbulence. its been proven that removing the screen actually hurts performance
__________________
GT-40X heads(58cc), Cobra upper and lower, 75 mm Bullet, Moroso fenderwell induction, FRPP 65mm TB, 24# injectors, black magic electric fan, phenolic spacer, 1.7 crane cobra roller rockers, crane 2031, BBK 1 5/8 equal length hearders, 2.5 inch off road pipe, 2.5 flowmaster catback, FMS 3.55 gears, T5-Z transmission, FRPP aluminum driveshaft, svo heavy duty clutch, mcleod bullet proff bellhousing, BBK adjustable cluth quadrant, hurst billet shifter, lakewood subframes, BBK strut tower brace, BBK 2pt lower cross bar, FMS 190 lph fuel pump, crane ps91 coil, FMS street pulleys, and 300+ race wires. All thanks goes to my wife sheri, jason, jeff, robby, my dad and all others you helped contribute. most importantly GOD!!! |
![]() |
![]() |
![]() |
#5 |
MW Link Sponsor
Join Date: Sep 2002
Location: rochester , ny
Posts: 79
|
![]() my screen is removed and my stock mas is honed , and it does not not affect performance in a negative way . it is ok to do as long as you have proper filtration of the air entering the engine , the purpose of the screen is to protect the tiny wires inside of it which measure voltage. the turbulence is not necesary because the sensor does not measure air frequency like some mas's do. electricity travels through the wires which heats them up and the incoming air cools it down , the more air that hits it , the cooler it gets , and more fuel is put into the engine . i also datalog my runs and i did not notice a difference in air fuel ratio . you can hurt your afr if you move your mas to a different location , or turn it . just my 2 cents .
|
![]() |
![]() |
![]() |
#6 |
Registered Member
Join Date: Sep 2002
Location: Los Angeles
Posts: 39
|
![]() I have an 89 gt that ran a best of 9.10 @ 75.16mph on an 1/8 mile with the screen in. I decided to remove the screen and then
ran a best of 9.06 @ 75.86. I was very pleased with this mod. as I picked up a little e.t. and mph. |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Getting a code 66, but mass air sensor seems to be within spec | crazypete | Windsor Power | 0 | 09-17-2002 07:32 AM |
mass air sensor question | whitepony91 | Windsor Power | 4 | 07-04-2002 01:40 PM |
Trick Flow "R" Intake on a stock 88 5.0??? | BowTie Eater 5 Liter | Windsor Power | 3 | 01-15-2001 09:44 AM |
LT's vs. shorties vs. stock headers | jonnyk | Windsor Power | 9 | 01-01-2001 11:28 AM |
air flow sensor wiring | carter | Modular Madness | 4 | 12-09-2000 09:43 PM |