CVR starter

elma22 · 10-05-2002, 11:43 PM

Does anybody know where you hook up the wire that goes to the small screw on a 1.9hp high torque starter from CVR? Any pics?

Thanks fellows

mustang man · 10-06-2002, 03:15 PM

I purchased a high torque starter from summit. If its the same as your cvr starter the small wire has to go to wire that energized your old solenoid, however the new starter needs a 12 vol feed source to energize, and the ford wire from the old starter is only 4 volts so I had to install a relay so it would work

drudis · 10-07-2002, 08:20 AM

If its anything like the newer mini starters, you might look at this wiring diagram:

elma22 · 10-09-2002, 11:09 PM

Thanks for the input. The drawing helped a lot.

Thanks

10-05-2002, 11:43 PM	#1
elma22 Registered Member Join Date: Jul 2001 Location: Montreal Posts: 45	CVR starter Does anybody know where you hook up the wire that goes to the small screw on a 1.9hp high torque starter from CVR? Any pics? Thanks fellows __________________ 1 5-8 full lenght headers Custom 3" exhaust with 3" high flow cats Flowmasters 40 series with pro dumps, MAC cold air fender induction, MAF conversion, cobra eec PRO 5.0 shifter, 3.27 gears, synthetic lube everywhere, 16deg timing, 155 fuel pump, king cobra clutch with bbk shifting cable, accel coil, 73mm brakes

10-06-2002, 03:15 PM	#2
mustang man Registered Member Join Date: Sep 1998 Location: Poy Sippi Wi. Posts: 111	I purchased a high torque starter from summit. If its the same as your cvr starter the small wire has to go to wire that energized your old solenoid, however the new starter needs a 12 vol feed source to energize, and the ford wire from the old starter is only 4 volts so I had to install a relay so it would work __________________ 87LX 351W, avenger heads, hooker headers, dynomax super turbo's, lots of other stuff to go fast

10-07-2002, 08:20 AM	#3
drudis Moderator Join Date: Dec 1999 Location: Livonia, MI, USA Posts: 1,194	If its anything like the newer mini starters, you might look at this wiring diagram: __________________ Darius Rudis, Moderator Corner Carvers Delight 1989 Mustang LX - Open Track Car http://www.dariusrudis.com

10-09-2002, 11:09 PM	#4
elma22 Registered Member Join Date: Jul 2001 Location: Montreal Posts: 45	Thanks for the input. The drawing helped a lot. Thanks __________________ 1 5-8 full lenght headers Custom 3" exhaust with 3" high flow cats Flowmasters 40 series with pro dumps, MAC cold air fender induction, MAF conversion, cobra eec PRO 5.0 shifter, 3.27 gears, synthetic lube everywhere, 16deg timing, 155 fuel pump, king cobra clutch with bbk shifting cable, accel coil, 73mm brakes

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Starter problem....still there	Hethj7	Windsor Power	18	07-23-2006 05:17 PM
Quick Starter Install Question	Evil Joe	Windsor Power	3	09-16-2003 08:50 PM
Putting in clutch pedal after starter install now produces very high pitched whine	crazypete	Windsor Power	3	08-18-2003 08:51 PM
Help!! Starter problem.	DRASTiK	Windsor Power	2	04-07-2002 03:51 PM
help quick, 93 starter in 87GT problems	fiveohpatrol	Windsor Power	2	06-21-2001 06:22 AM