![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Sep 2000
Location: Halifax,Nova Scotia, Canada
Posts: 30
|
![]() Which set of long tube headers fits aods the best?
|
![]() |
![]() |
![]() |
#2 |
347ci of HORSE POWER!!!
Join Date: Jul 2001
Location: Houston, TX
Posts: 1,416
|
![]() I like my BBK long tubes, but I have a TKO 5 speed. I "think" they will fit just as good.
|
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Mar 2000
Location: Springfield, Ma, usa
Posts: 706
|
![]() I know for sure that MAC and Bassani make longtubes designed to fit around the AOD. I'm not too sure it BBK does, but they might.
__________________
NewEngland Auto www.baystategearheads.com -91 Mustang Coupe, ex 4cyl (sold) -99 F150, 3" lift, 35" Procomps, Magnaflow exhaust |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Mar 1999
Location: Amarillo, Texas, USA
Posts: 780
|
![]() We've got BBK long tubes on one car and BBK equal length shorties on the 331 Stroker, I didn't install the shorties but the long tubes were a lot of fun to get in. Once in place everything fit like it was actually designed to. It's a little tight on the driver's side near the steering shaft but I understand all long tubes are close.
One word of caution, you have to get the engine really up there to get the passenger side in and if you're not careful you can break the heater core inlet pipes (this sux believe me). I'm guessing but I don't think you have to raise the engine to install the shorties.
__________________
1986 four-eyed LX coupe, 358 Cleveland, Tremec TKO600/centerforce clutch, dish cut Probe forged pistons, comp cams hyd.roller cam, .579/.588@224/230, Edel.performer, 670 holley street avenger, CPR custom built long tubes, ported and polished 4bbl heads, manley valves, beehive springs, MSD peo-billet dist/MSD6AL, fluidamper, 5 lug conv. with 17x8 bullits there's more but it's still not finished yet. Oh, and the oldest boy is turning his 89 GT into a FFR cobra this next summer. |
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: Mar 1999
Location: Ocean City , Maryland
Posts: 344
|
![]() first off why ? is the question you ask yourself . if you have a fairly moded 5.0 ,you would still ask this question . If your dynoed at 350 hp then maybe . If not , don't give yourself headaces . cause you don't need any ( and we could go into this forever ) if headers are your cure ! unequal length , there are many , anymore than $160 ,your paying to much . and the ease of install
![]()
__________________
1991 5.0 NotchBack,Black as of 05/04/09 34,300mi. 2001 LIGHTNING Black 29,872 mi. 05/04/09 (Hangar Queen) SMOKEM UP |
![]() |
![]() |
![]() |
#6 |
Registered Member
Join Date: Mar 1999
Location: Amarillo, Texas, USA
Posts: 780
|
![]() You do have a point. Long tubes are geared more toward high horsepower use and for most street applications, the shorties would work fine. My son who has the long tubes started with a plan he knew would take several years to complete and eventually he is hoping for around 450 horses with the blower . . .BUT, that's still a few months off and he still has some heads to buy first. It's gettin there but it takes time. FYI.. . .the 88 with the shorties pulls like a bull, harder than the 351-C in the 82 and the only mods it has are MSD 6AL, shorties and a Mallory coil, True, it is a 331 and I guess this accounts for a bunch of the torque but probably wouldn't benefit from long tubes until a lot more "stuff" is added.
__________________
1986 four-eyed LX coupe, 358 Cleveland, Tremec TKO600/centerforce clutch, dish cut Probe forged pistons, comp cams hyd.roller cam, .579/.588@224/230, Edel.performer, 670 holley street avenger, CPR custom built long tubes, ported and polished 4bbl heads, manley valves, beehive springs, MSD peo-billet dist/MSD6AL, fluidamper, 5 lug conv. with 17x8 bullits there's more but it's still not finished yet. Oh, and the oldest boy is turning his 89 GT into a FFR cobra this next summer. |
![]() |
![]() |
![]() |
#7 |
Registered Member
Join Date: Mar 1999
Location: Amarillo, Texas, USA
Posts: 780
|
![]() I almost forgot, the instructions that came with the long tubes said they will not work with an AOD.
__________________
1986 four-eyed LX coupe, 358 Cleveland, Tremec TKO600/centerforce clutch, dish cut Probe forged pistons, comp cams hyd.roller cam, .579/.588@224/230, Edel.performer, 670 holley street avenger, CPR custom built long tubes, ported and polished 4bbl heads, manley valves, beehive springs, MSD peo-billet dist/MSD6AL, fluidamper, 5 lug conv. with 17x8 bullits there's more but it's still not finished yet. Oh, and the oldest boy is turning his 89 GT into a FFR cobra this next summer. |
![]() |
![]() |
![]() |
#8 |
Registered Member
Join Date: Mar 1999
Location: Ocean City , Maryland
Posts: 344
|
![]() that is good , we are talking a killer stang ! next is e-bay to get rid of them,and get ones that fit !! Good Luck with this stang ,and your boys
![]()
__________________
1991 5.0 NotchBack,Black as of 05/04/09 34,300mi. 2001 LIGHTNING Black 29,872 mi. 05/04/09 (Hangar Queen) SMOKEM UP |
![]() |
![]() |
![]() |
#9 |
Registered Member
Join Date: Sep 2000
Location: Halifax,Nova Scotia, Canada
Posts: 30
|
![]() So what do you guts recomend for shorty headers. My current setup produces right around 390 hp. I have headman 1 5/8 unequals on now.. Thanks
|
![]() |
![]() |
![]() |
#10 | |
Get down.....
Join Date: Apr 2001
Location: Room 103
Posts: 2,095
|
![]() Quote:
__________________
Cobra brakes are on! Finally..... ------------------------------------------------ |
|
![]() |
![]() |
![]() |
#11 |
Registered Member
Join Date: May 2001
Location: westerville, OH USA
Posts: 618
|
![]() I got the MAC equal lengths, their not bad but the tubes are a ***** to manipulate if you take them back off and then try to get the bolts started to put them on. When I get new exhaust I'm going with some full length BBK/dr. Gas Xpipe/single or two chambers w/turndowns.
__________________
1990 Notchback: BBK Ceramic Coated Full length headers, Dr. Gas 3"- 2 1/2" x-pipe, Flowmaster 40's/turndowns. |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
SVO Shorty Headers 1-5/8 Question | stangposse | Windsor Power | 0 | 08-07-2003 12:48 PM |
Buying new headers | TwiLighTBluEGT | Windsor Power | 4 | 04-23-2003 08:55 PM |
Anyone have problems with MAC headers?? | HiFlow5 0 | Windsor Power | 15 | 05-30-2002 08:30 AM |
Headers should I or shouldn't I....Need Advice Quick Please | Mustang_GT_90 | Windsor Power | 9 | 05-01-2002 01:16 PM |
BBK one-piece flange or MAC individual flange long tube headers. | Fox Body | Windsor Power | 10 | 04-03-2001 04:25 PM |