© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
12-03-2002, 03:38 PM | #1 |
Registered Member
Join Date: Nov 2002
Location: Gatineau, Qc, Canada
Posts: 62
|
Where can I buy a check valve?
That opens up under boost?
Nik |
12-03-2002, 04:12 PM | #2 |
Mustang Enthusiast
Join Date: Mar 2002
Posts: 528
|
I don't know if this is what you're looking for
but I found it on Powerdyne's website. Take care, Keith
http://www.proficientperformance.com...ode=A10261-011 |
12-04-2002, 08:30 AM | #3 |
Registered Member
Join Date: Nov 2002
Location: Gatineau, Qc, Canada
Posts: 62
|
Thanks, that's exactlt what I was looking for. Sorry to say but this is a ripoff! 140$ for a plastic valve.
BTW this is for using a supercharger with SD. I wonder if a PCV valve would work? Nik |
12-04-2002, 08:40 AM | #4 |
Registered Member
Join Date: Nov 2002
Location: Gatineau, Qc, Canada
Posts: 62
|
That setup doesn't use a T fitting. Seems the valve assembly does it for you. The setup I was thinking of using was a T with the valve on one end.
Nik |
12-04-2002, 08:52 AM | #5 |
Junior Member
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
|
__________________
Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local
RED & WHITE! |
12-04-2002, 12:13 PM | #6 |
Registered Member
Join Date: Nov 2002
Location: Gatineau, Qc, Canada
Posts: 62
|
Are you suggesting I convert to MAF
Nevermind though, I located some! Here's my situation. I want to install an A-Trim (around 6psi max) on my Speed Density '87 Mustang. The problem is that around 3500rpm the engine will bogg and I might also experience idle problems due to the MAP sensor not beeing able to read boost. In order to rectify the situation, I need to install a check valve on the vaccum hose between my intake and MAP sensor. Note: Under boost the FMU will variate the fuel pressure. My question is, what cracking pressure should my valve have? A low one like 0.8 psi or higher like 2, 3 or 4 psi? thanks, Nik |
12-04-2002, 12:56 PM | #7 | |
Junior Member
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
|
Quote:
__________________
Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local
RED & WHITE! |
|
12-04-2002, 01:16 PM | #8 |
Registered Member
Join Date: Nov 2002
Location: Gatineau, Qc, Canada
Posts: 62
|
Yes, I saw thoses. they are BOV's... I was refering to a check valve to put between the intake a MAP. For a supercharge speed density application...
Now my question is; what cracking pressure should it have? 0.8, 2, 3, 4 psi? nik |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Speed Secret # 4 | jim_howard_pdx | Windsor Power | 13 | 11-10-2002 03:42 PM |
Will my stock or aftermarket h-pipe bolt up to a 4 valve? | Redstang96 | Modular Madness | 0 | 08-29-2002 09:56 PM |
Adjustable Proportioning Valve (Brakes) | RMARIANI | Windsor Power | 2 | 07-05-2001 06:27 AM |
Valve Springs & Roller Rockers | StreetStang37 | Windsor Power | 4 | 04-17-2001 03:54 AM |
PCV Valve what the ?@#$@#$@$ | Chevyguy | Windsor Power | 3 | 04-11-2001 08:01 PM |