![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Jul 1999
Location: RI, USA
Posts: 51
|
![]() Need help getting pilot bearing out of crankshaft...
O.K. Tried the grease method, not gonna happen. Don't have one of those nifty slide puller things. Any suggestions? Where can I get a tool to do this? Can I make a tool? Anywhere I can buy one cheap??? HELP!!!!! Thanks -Troy ------------------ 1995 GT Convertible K&N, Steeda G-Trac Stage 3 Suspension, Pro 5.0 Shifter, Kenny Brown Extreme Sub System, Ford Racing Underdrive Pulleys, Cobra R Rims, Steeda Adjustable Clutch Quadrant & Cable |
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Oct 1999
Location: Cincinnati, Ohio
Posts: 1,575
|
![]() Mine was in good too. I tried the puller and it wouldn't budge. So I ended up using a chisel and a dremel tool and got it out. Good luck man!
------------------ 87 GT, 4 inch cowl hood,17x9 Cobra R's/255/45's,GT-40 heads,long tubes headers,h-pipe,Flows,BBK cold air, Mass air,70mm MAF, 1.7's, 1" spacer,underdrive pulleys,Pro 5.0, King Cobra, Adj. fuel Reg., Lakewood Lift Bars,50/50's,subframes, 4.10's. Best time 13.012 Best MPH 104 Best 60' 1.816 Visit my site at: http://www.geocities.com/cobrar93_2000/MyPage.html |
![]() |
![]() |
![]() |
#3 | |
Registered Member
Join Date: Oct 2000
Location: Ontario, Canada
Posts: 234
|
![]() Quote:
------------------ 82 Mercury Capri 302. Comp. Cams Tremec 3550 3.73's 12.8@106 N/AKevin's Capri |
|
![]() |
![]() |
![]() |
#4 |
Procharged!
Join Date: May 1999
Location: Hanover, PA
Posts: 1,539
|
![]() Here's a old trick I learned from my dad. Pack the hole with soaking wet paper towel and use a punch or something that is just big enough to fit inside the hole to pack it in, the bearing will pop out due to the pressure of the towel and water, and it won't hurt a thing
![]() ------------------ My Ride Check Out My Site 91GT, Holley SysteMAX II Kit-Heads 2.02" x 1.60",Full MAC exhaust 1-5/8" Long tubes, 2-1/2" O.R H-Pipe, 2 1/2" cat back, 12" K&N Filter, RNH PERFORMANCE Ram Air, Ron Davis Radiator, Full Suspension,3:73's, Welds, Best on new motor-12.60 @ 108, no traction 1.98 |
![]() |
![]() |
![]() |
#5 |
Guest
Posts: n/a
|
![]() You can rent a tool from the auto-part store for free usually (they just need a deposit on the tool). If you are having trouble getting it out with the puller, make sure you are biting on the little indentions on the back of the pilot bearing. (If you don't have a new pilot bearing, go buy one so you can tell where the indentions are and place the jaws of the puller in these indentions). I couldn't get mine out either, until I looked at the new pilot bearing and noticed the indentions. Otherwise there is nothing for the jaws to bite into. Good luck and let us know what happens.
|
![]() |
![]() |
#6 |
Registered Member
Join Date: Apr 1999
Location: Grass Valley, CA, USA
Posts: 1,389
|
![]() I just took mine out today.
I used the backside of a chisel (it fit) and fortunately there was enough grease in the thing to work. make sure there aren't air bubbles and whack it a few times with a hammer just like the paper towel method above. I'm glad it worked, cuz i really want to get my car running! |
![]() |
![]() |
![]() |
#7 |
Registered Member
Join Date: Apr 1999
Location: Hayes, Va, USA
Posts: 798
|
![]() Yeah I wuz gonna say, pack that rascal with bearing grease, find the tightest fitting socket (without any interfernce) put it in backwards then put an extension in the hole to plug things up, give it a whack and hydraulic the sucker out of the crank.
|
![]() |
![]() |
![]() |
#8 |
Registered Member
Join Date: Jul 1999
Location: RI, USA
Posts: 51
|
![]() Thaks for all the replies! I'll give it a try again Wednesday. I think the grease I was using was too thin. I'll use heavy grease this time.
-Troy ------------------ 1995 GT Convertible K&N, Steeda G-Trac Stage 3 Suspension, Pro 5.0 Shifter, Kenny Brown Extreme Sub System, Ford Racing Underdrive Pulleys, Cobra R Rims, Steeda Adjustable Clutch Quadrant & Cable |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Does the T-5 pilot bearing need to come out for an AOD to go in? | crazypete | Windsor Power | 14 | 11-06-2003 11:04 PM |
Pilot Bearing | Cody2552 | Windsor Power | 2 | 04-09-2003 09:30 AM |
Pilot Bearing | Falcons Talon | Windsor Power | 13 | 10-16-2002 06:44 PM |
Pilot bearing replacement | Rebel79 | Windsor Power | 8 | 05-31-2002 02:12 PM |
roller pilot bearing part # | Strim91GT | Windsor Power | 0 | 04-23-2001 02:12 PM |