© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
10-10-2003, 10:17 AM | #1 |
Registered Member
Join Date: Oct 2003
Location: west palm beach fl.
Posts: 2
|
stops at 3,200!?!?!?
hey guys i just finished building the top end of my car and i went for a test drive yesterday. the car drove great and had a lot more power low end but when i floored it it went to 3,200 hundred rpms and stopped there. if i let up off the gas some it would keep goin but i cant floor it for some reason. it feels like it hits redline at 3,200. if i half throttle it it will eventually make its way up but i cant race at the track wit half throttle. i will list my mods done to my car at the end. any help is appreciated thank you.
mods:comp polymers upper intake,gt-40 lower intake, stock heads ported w/ 1.94, 1.6 valves, adjustable roller rockers 1.7, comp cams wolverine racing cam., removed a/c and smog converted to mass air, full exhaust shorty equal length headers, 3:73 gears, underdrive pulleys, gear-to-gear timing, cold-air induction, 255 lph fuel pump, throttle body 65mm and egr spacer. |
10-10-2003, 10:28 AM | #2 |
Registered Member
Join Date: Mar 2003
Location: philadelphia ms
Posts: 180
|
i've run into a simmilar problem i couldnt figure out before.. it was on tireburners car.. he had to dissasemble before we found the problem.. PM him and he could probably give u some insite. but i dont think thats your prob...
|
10-10-2003, 02:03 PM | #3 |
Registered Member
Join Date: Apr 2001
Location: Gallatin, Tn
Posts: 1,326
|
Had the same problem on a car I worked on, did the same thing on test drive but it stopped pulling at 4200, it was the timing, though simple, timing is everything with these cars. Check it out and let us know what it's set at and adjust it a little to play with it. Good luck.
__________________
|
10-10-2003, 06:21 PM | #4 |
RICE taste like Chicken
Join Date: Jun 2000
Location: Edmond, OK
Posts: 687
|
I had the same prob. It is because you aren't getting enough spark under WOT. I didn't have a Ignition box. I bought one and it fixed it.
__________________
Dustin 89 Saleen GT Sport Supercharged 306 Started her up 6/8/03 Old Motor Supercharged 347 516 rwhp 553 rwtq 11.249@126.83 1997 Honda CBR 1100XX Super Blackbird 162 hp |
10-11-2003, 03:14 PM | #5 |
It's a lot like a race car
Join Date: Aug 2000
Location: Meridian, MS
Posts: 4,130
|
Things to check:
1) timing 2) fuel pressure If those don't fix the problem check out and test the: 1)TFI module 2)coil 4)plugs and plug wires That Wolverine cam and those 1.7 roller rockers arn't maxing out your springs are they? Stock springs on the E7's are only good too to like .500 lift Weak valve springs maybe? -Josh, aka the tireburner
__________________
1987 Buick T-type 1998 HD Electra Elide |
10-12-2003, 11:34 AM | #6 |
Registered Member
Join Date: Oct 2003
Location: west palm beach fl.
Posts: 2
|
ok, i know its not the timing because i had the shop do that. thats not exactly my strongest point. they had the spout connector disconnected when done. i also upgraded springs so i know its not the springs. but it is quite possible that it is the no spark at wide open throttle. i have never upgraded the ignition box. but i guess it doesnt matter because im leaving for the navy in 3 weeks and my radiator went out on me. not only that tranny fluid was leaking in my colling system and i think water got into my tranny fluid. so i got bigger problems now. but n e ways im just goin to wait until a year down the line when i save enough money to buy a race block. ive been looking into the 347 pro bullet race blocks from dss. racing. if you guys read mm&ff. you should know what i mean. anyways i want to thank everybody for there help with this. but i guess its too late to fix a car that has had problems from the beginning.
|
10-12-2003, 02:32 PM | #7 |
Factoy Five Roadster
Join Date: May 2000
Location: Sevier Co,Tennessee
Posts: 1,681
|
Sounds like MAF needs to be calibrated.
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Weird Shifting problem after installing a Tri-Ax shifter ?? | Katmandu | Windsor Power | 11 | 04-19-2004 09:41 AM |
my pro 5.0 rattles against the stops | Conman | Windsor Power | 7 | 10-17-2002 04:20 PM |
Strut Bump Stops? | Jeff Chambers | Windsor Power | 0 | 05-23-2002 09:23 AM |
the heartbeat stops here | blackvert00 | Blue Oval Lounge | 23 | 05-17-2002 05:56 AM |
IT STOPS!!!!! | LOCASH | Windsor Power | 0 | 01-05-2001 04:14 AM |