![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Import Slayer
Join Date: May 1999
Posts: 2,241
|
![]() My passenger door handle broke and you can't open the door anymore from the outside. I bought a new(metal) handle for it but I would like to know how hard a job it's going to be.
I looked in my Haynes manual but I found nothing about handles. The factory ones look like they are pop riveted on. It looks as if I am in for some drilling. ![]()
__________________
'82 GT 351W (.060)Comp Cams 274* Extreme Energy cam, ported & polished heads w/ 1.94/1.60 valves 10.3:1 flat top pistons,stealth intake, Mallory dizzy,Holley 750dp carb, BBK shorties,Flowmaster exhaust,C-4 with 3700 stall converter, B&M pro shifter,8.8 rear, 4:10's, subframes, electric fan, powermaster alternator, 4 core radiator. |
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Sep 2003
Location: st. louis, MO
Posts: 197
|
![]() Its not hard at all...just drill out the rivets, pop of the little things holding the handle in, and put the new one in with nuts and bolts. I just put new ones on both sides cause the old ones looked like crap. Hope that helps, but the job is pretty basic.
__________________
98 Cobra, CAI, Flowmasters, o/r h-pipe. 4.10s, Hurst shifter. |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Apr 2000
Location: Edmonton,Alberta,Canada
Posts: 317
|
![]() Ya its relatively easy. Just drill out the old ones and you can either bolt in the new ones or use the rivets they come with.
__________________
Fast Company |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Jul 2001
Location: Edison, NJ, USA
Posts: 125
|
![]() I did the same for my drivers side handle a few weeks ago, I ordered the heavy duty rivet gun, door handle and rivet set from 50resto.com. The gun was $25, real easy to use.
If you get the gun, don't lean into the gun after the second pump of the handles...when the rivet finally pops the gun jumps back and if you are leaning into it you'll wind up scratching the paint. Take care, Rich D. |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
ball joint replace in a 65 - how hard is it? | Steriti | Classic Mustangs | 5 | 07-03-2004 05:32 PM |
T5 hard to shift after replacing bearing retainer | Merlin76 | Windsor Power | 8 | 02-20-2004 10:22 PM |
replacing side view mirror...how hard? | 82 GT | Windsor Power | 2 | 02-11-2004 11:31 PM |
replacing hard brake lines | 82 GT | Windsor Power | 0 | 05-26-2002 02:57 PM |
Replacing convertible top. How hard is it? | Dark_5.0 | Windsor Power | 7 | 06-09-2001 09:01 PM |