![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Apr 1999
Location: penfield, ny, u.s.
Posts: 78
|
![]() Hey just a quick question,
Is there a way i could tighten down my headers so that my freakin car doesnt sound like crap. is there any bolt adhesive or something i can put on them so they wont come loose every month or so?
__________________
'89 lx 5.0-FLowmasters, H-pipe with cats, 373's, pulleys, BBk headers Best 1/4 mile- 14.1 @98 mph (67 deg. 90+ humidity) ![]() ![]() Nitto DR's 245/50R16 NOS hopefully 100 shot ![]() |
![]() |
![]() |
![]() |
#2 |
dude5l
Join Date: May 2001
Location: Grande Prairie, Alberta, Canada
Posts: 603
|
![]() Any thread locker (loctite) will not stand up to the heat except for Loctite "red", and then you will never get them out without using a torch. There is a company that sells a special locking bolt for headers, it uses a c-clip and a peice that rests against the header to stop it from turning, but I forget the name of them. Maybe somebody else will remember.
__________________
Good luck! Brad R. 1992 L.X. 5.0 coupe MODS: A few little bolt ons ![]() New Best time ...11.60 @ 128 mph @ 2000+ ft altitude. Rice Haters Club member #39 Users rides #2542 |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Aug 2001
Location: Huntington NY
Posts: 573
|
![]() Stage 8 makes the locking header bolts.
__________________
-1993 Mustang, 900rwhp 03-04 cobra based 4v swap, full Griggs setup, project underway -1994 Ranger w/ 427cid windsor (daily beater) check it out! |
![]() |
![]() |
![]() |
#4 | |
Registered Member
Join Date: Jun 2003
Location: Wisconsin
Posts: 348
|
![]() Quote:
__________________
92 Mustang GT, 347 Stroker(Forged Steel Crank/Rods-Balanced, Forged Aluminum Dished Pistons), Trick Flow Track Heat Intake, Trick Flow Twisted Wedge Heads w/ Stage 3 port/polish, 80mm C&L MAF, FMS 30# Inj., BBK AFPR, Trick Flow Stage 2 Cam, Trick Flow 1.6R Rockers, BBK E.L. Headers, Flowmaster Cat-Back, MAC CAI, FMS Pulleys, Griffin Alum. Radiator, MSD Pro-Billet Distributor; AOD, Dynamic 3300 Lockup Converter, B & M Super Cooler, B&M Ratchet Shifter; 3:73 gears. |
|
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Exhaust leak | StateTroopCoupe | Windsor Power | 1 | 09-25-2003 08:21 AM |
Help!! Exhaust Leak | 1991GT | Windsor Power | 5 | 12-13-2002 09:39 PM |
Speed Secret # 4 | jim_howard_pdx | Windsor Power | 13 | 11-10-2002 03:42 PM |
Header gaskets | Stang951 | Windsor Power | 18 | 11-01-2002 05:57 PM |
Exhaust leak? | oamunoz | Classic Mustangs | 4 | 07-13-2001 03:00 AM |