![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Senior Member
Join Date: Apr 1999
Location: San Angelo, TX
Posts: 377
|
![]() I'm closing in on the time to make my car run.
![]() Here's the goal: 12 second Daily Driver! Honestly low 13's would be fine, but I'd love to see 12s. I want to design a plan so that every dollar I spend will go towards my goal. I know I'll have to get a roll cage, but I figure I should get it out of the 15's before I get one. ![]() Figure I'd start with a block. Which one should I get, 302 or 351? Only concern I have is having to replace my hood, I really like it. ![]() I do plan on building an entirely new drivetrain but, if the stock 8.8 rear will support the final results should I consider getting 3.73's now? I imagine 4.10's, which would be ideal now, would be a bit much with a stronger engine. I know this is going to take awhile, but someday I will accomplish it. Then when I'm finished and I have an article on pg 52 of MM&FF, I'll be proud to say, "I couldn't have done it without all the great advise from the members of MustangWorks.com"! ------------------ '95 GT Convertable |
![]() |
![]() |
![]() |
#2 |
Tires Fear Me...
Join Date: Jan 2001
Posts: 867
|
![]() If you go with a 351, you are going to run into many expensive changes.
I would stick with a fresh 302 and get a setup such as Skymans or Ricks91GT..They are deep into the 12's... Good luck. ------------------ 347 Stroker Motor: Balanced, Cobra Transmission, Extrude Ported and Polished Upper and ported Lower, GT40 Milled Ported and Polished Heads, B303 Cam, BBK 1 5/8 Headers, 30lb Bosch Injectors, Holley AFPR, March Underdrive Pulleys, Perma-Cool Fan, 3-Core Radiator, Accel Performance Coil, Accel 300+ Racing Wires, Ram Air, K&N Filter, 73mm Vortech MAF, 70mm TB, FlowMaster Exhaust w/BBK Offroad H-Pipe, Hurst Shifter, 3:55 Gears, Ram Clutch, Cross Drilled Rotors, AC and Smog del, rear seat del. |
![]() |
![]() |
![]() |
#3 |
Mustangs
Join Date: Jul 2000
Posts: 1,938
|
![]() I agree with smokedawg, changing to a 351 would require to begin with a new hood so i won't get into the specifics of that swap. Basically if you have a good induction/exhaust system matched for a higher rpm band and gears and add a supercharger to that you'll EASILY get at least into the 12's. I've heard that a holley systemax kit will get most vehicles anywhere between the mid-high 12's depending on the driving, but then again you have a convertible which is pretty heavy. If money is no object, then my limited opinion is a holley systemax II kit (because it's all flow/powerband matched as a kit), a 9 psi supercharger like a Vortech S-trim, Paxton NOVI2000, etc. at least 1 5/8" primary headers with 2 1/2" dual exhaust, maybe even 1 3/4" with 3" dual exhaust becuase i believe you'd be pushing close to 450 horsepower or even more.
You could also get a stroker short block setup to go with the systemax II (or whatever you choose) like a 331 or 347 to increase torque output for your heavy vehicle and having a supercharger would also greatly enhance your off the line launch. To go with all the extra power i believe that you'd need things like 30# injectors with a calibrated MAF sensor, maybe even a larger fuel rail, 255lph fuel pump, i don't know but maybe you may need to swap to larger fuel lines in general as well. A custom burnt chip dyno tuned chip would also be a good investment. These are just some ideas and i'm sure everyone will have something good to share. I hope this was inspiring or helpful somewhat ![]() -side note: unless you want to change to carburetion, a BOSS 302, which is has cleveland heads would probably not do very well in your daily driver criteria. ------------------ previous name: 84stangLX '84 Mustang 5.0 LX my LX '89 Mustang GT my GT |
![]() |
![]() |
![]() |
#4 |
Senior Member
Join Date: Apr 1999
Location: San Angelo, TX
Posts: 377
|
![]() Thanks guys, keep it coming.
84LX89GT - About the BOSS, what I was primarily concerned with was the block. I figured the heads would probally be replaced with something better than stock reguardless of how good they were. Thanks for the advise though, I learn somethin new everyday. |
![]() |
![]() |
![]() |
#5 |
Guest
Posts: n/a
|
![]() Stick w/ the 302...the 351 is an awesome motor, but Smokedawgs right, it'll end up being way too expensive, just for a 12 second car. Check out the set ups of us w/ 12 second cars, and see which you like, don't like and possibly mix and match
![]() ------------------ '90 LX 5.0;12K original miles (no sh*&);3.55 gears; March pulleys;Edelbrock Performer Heads;BBK 1 5/8" equal length shorties;MSD 6AL ignition w/ blaster 2 coil;FMS E303 cam;Pro-M 75mm MAF;BBK 70mm TB; Eibach drag-launch spring kit;Southside welded subs;9" K&N cone filter charger;Hurst shifter;Cervini's 3" turbo hood;A/C delete; gutted cats;2 chamber Flomasters;Corbeau racing seats;FMS 30# injectors;JMS chip; Holley 190lb fp;TFS track heat Intake (12.299 @ 113 - 1.78 60') |
![]() |
![]() |
#6 |
I'd rather be basketweaving
Join Date: Feb 2000
Location: Indianapolis
Posts: 2,551
|
![]() its fairy easy to take a fox LX into the 12's but you guys have to notice that he's got a SN95 vert. im hoping its not an automatic? cause that would make it even harder
if it were me, i'd go with a sportsman 302 block just for peace of mind, with a 331 stroker kit from DSS, AFR185's, GT40 intake (or holley intake if a supercharger is in mind) not sure what cam specs to tell ya, but im sure with these and some dragradials you'll be running well into the 12's ------------------ 88 Notch, B&M Ripper, 3.73's, Ported E7's, Explorer int. w/ ported lower, pulleys, 1.7RR's, BBK headers, off-road H-pipe, flowmasters, subframes, 65mm TB, March ram air ,MSD coil, U/L control arms, 155lph f/p, Crane Adj.FPR, Nitto drag radials, best 1/4--> 13.76@101.4 on a 2.17 60ft |
![]() |
![]() |
![]() |
#7 |
Senior Member
Join Date: Apr 1999
Location: San Angelo, TX
Posts: 377
|
![]() Oh ya... this things a slug! Convertable and AODE!
That's why I'm looking for a little bit of help, there aren't many SN95 verts running that quick. |
![]() |
![]() |
![]() |
#8 |
Registered Member
Join Date: Aug 2001
Location: Palm Beach Gardens, Florida, USA
Posts: 191
|
![]() Make sure when you order a cam that you contact a company like JMS and provide them with the motor and cam specs so they can burn you a custom chip. 94-95 EEC-IV's don't like to idle with aftermarket cams unless the chip is burnt for your application. I have a 95 coupe, some bolt-ons, and eventually I will break the twelves. It feels like a 14 second car now, and I notice it really doesn't have much to offer once I slam third gear. But then again, I know I will need the entire upper half of the motor done up to run that quick in this car. It was so easy with my Chevelle, 350, 10:1, stock iron heads and cheap a$$ TRW flat tops. Ran easy 11.90's in a heavy car. Oh well, the stang is pretty damn easy on the eyes though.
------------------ Todd 1995 GT/T-5 Pulleys; 65 mm TB; Flowmaster cat-back; Mac off road H-pipe; FMS aluminum driveshaft; short-throw shifter; HD clutch; Cobra R's; Cobra front and wing |
![]() |
![]() |
![]() |
#9 |
I'd rather be basketweaving
Join Date: Feb 2000
Location: Indianapolis
Posts: 2,551
|
![]() your definately gonna need to either swap to a T-5 or get a Lentech (or equiv.) with about a 2800-3000 stall converter
oh yah i just read a post a couple weeks back of a naturally aspirated SN95 vert breaking into the 12's, i believe his name is killercanary ------------------ 88 Notch, B&M Ripper, 3.73's, Ported E7's, Explorer int. w/ ported lower, pulleys, 1.7RR's, BBK headers, off-road H-pipe, flowmasters, subframes, 65mm TB, March ram air ,MSD coil, U/L control arms, 155lph f/p, Crane Adj.FPR, Nitto drag radials, best 1/4--> 13.76@101.4 on a 2.17 60ft |
![]() |
![]() |
![]() |
#10 |
I need 110mph Trap Speed!
Join Date: Feb 1999
Location: So, CA
Posts: 4,315
|
![]() You could copy my combo. Lots of lowend torque. Peaks about 5500rpm so its great for a daily driver. I get 23 mpg on the freeway at 70mph.
It goes mid 12's on motor, and 11's on the N20. (As soon as I get to spray it at the track) Skyler ------------------ -1989 Saleen Mustang #406- TFS TW Heads, E-303, Edelbrock intake, 70mm TB, 73mm MAF, 24lb injectors, 1 5/8 shorties, Off Road H, 3 Chamber flows, Jaz Race seats, Back seat removed, sub-frames, Roll Cage, and a 80 shot of N20. 12.54@107.4 Motor 332RWHP, 350rwtq |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Thoughts on Combo? | Rosco | Windsor Power | 9 | 06-03-2004 06:07 PM |
Anyone here run a similar combo and if so, what times did it run? | slowfive0 | Power Adders | 3 | 02-02-2004 01:39 AM |
Small block Combo ??'s | Coupe Devil | Windsor Power | 8 | 12-06-2002 12:17 AM |
Carb Combo | 86GT | Windsor Power | 8 | 08-24-2002 07:23 PM |
BAD @SS N/A 351w Combo? (Long) | BowTie Eater 5 Liter | Windsor Power | 0 | 02-27-2001 10:47 PM |