© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
03-01-2005, 12:28 AM | #1 |
Registered Member
Join Date: Sep 2002
Location: cent.wis
Posts: 203
|
ring size on stock pistons
What is the ring size on a stock 92 302 piston? I bought the speed pro file fit and they are ok on the 1st and 2nd ring but the oil ring is too loose. the only sizes shown in the summit book are 1/8th or 3/16's for the oil ring.(3/16) would be smaller right? And is it normal to have to file fit 45 thousandths off the rings? One more thing, is it a must to use a ring expander to get the rings on? I read a article in one of our favorite mustang mags were they said it is a must? Can't I just thread them around the piston?
|
03-01-2005, 07:08 AM | #3 |
Registered Member
Join Date: Sep 1998
Location: Oviedo, FL
Posts: 992
|
Re: ring size on stock pistons
AS nastyyn8 said above the 1/8 is smaller.
You don't NEED a ring expander to install them, it just makes it easier. I personally don't use one. I thread them. Now, you have to be very careful, cause the rings are very hard and brittle and will break easily. Also, don't nick or scratch the piston as you're installing them. Take your time filing them. It is very easy to file too much off.
__________________
"Support our Troops" Dave 1968 Cougar 2004 Thunderbird 2007 F150 Harley-Davidson, SuperCrew 1986 LTD 1997 Ranger 1992 Honda Civic |
03-01-2005, 10:02 AM | #4 |
Registered Member
Join Date: Sep 2002
Location: cent.wis
Posts: 203
|
Re: ring size on stock pistons
thanks for the info, I'll get on the horn and re-order new rings again. I'll also try to get a set that doesn't require so much filing.
|
03-01-2005, 04:57 PM | #5 |
Registered Member
Join Date: Sep 2004
Location: jersey
Posts: 147
|
Re: ring size on stock pistons
ols0051 just Curious, did a machine shop do the block for you? Or did you do it your self? I have an extra block and was thinking about trying to rebuild it my self.
|
03-03-2005, 01:48 PM | #6 |
Registered Member
Join Date: Sep 2002
Location: cent.wis
Posts: 203
|
Re: ring size on stock pistons
I guess the rings are metric.1.5mm,1.5mm and 4mm? surfsup. I got the shortblock used with 80k mi on it. We took it apart, cleaned it, and run a rabbit turd hone thru it. Got all these fancy measuring tools from a friend, all checked out perfect. It's fun because it's the first one for me, but without experienced help I would have just bought one from a place like DSS.
|
03-10-2005, 06:33 AM | #7 |
Rat Killer
Join Date: Aug 2002
Location: Cold ass Ohio
Posts: 1,143
|
Re: ring size on stock pistons
Rabbit turd hone? LMAO Make sure you clean that stuff outta there!
I'm running Total Seal rings, haven't found better ones out there. If you're planning on running N2O alot, leave a little extra end gap. The nitrous heat expands the rings, and there goes your end gap!
__________________
d-Con Racing "Nothing fancy, just 347 inches of RAT POISON!" MICE need not apply..... |
03-12-2005, 09:24 AM | #8 |
Registered Member
Join Date: Sep 2002
Location: cent.wis
Posts: 203
|
Re: ring size on stock pistons
I called summit and they say they are metric. But still waiting for them as they are on back order. They are not file fit. I wanted file fit rings because the plan is to use nitrous. But I also wasn't going to spray it until it was running perfectly. And as the summers seem to just fly bye it could be next year for that as slow as this thing is coming together. And next winter I was going to buy a new crank,rods,and pistons. What is the difference between file fit and non file fit? The non files just are made a spec right? or wrong? If I decide to open the gap up a bit I can right?
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Piston Ring Install Question | rancheroo | Windsor Power | 3 | 02-20-2004 10:07 PM |
Stock Tire Sizes | GhettoPop | Windsor Power | 8 | 01-19-2003 07:22 PM |
AFR 165's or other heads with cam and stock induction | Mustang_GT_90 | Windsor Power | 27 | 11-25-2002 03:01 PM |
Suspension ?--Bullitt, Eibach, Stock, or COMBO??? | rel3rd | Windsor Power | 3 | 10-15-2002 07:53 PM |
Stock pistons - Are they supposed to be flycut already? | 2FastLX | Windsor Power | 3 | 03-15-2001 01:17 PM |