![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Sep 2005
Posts: 6
|
![]() Hi, I am in the process of putting in a new transmission , drive shaft, and a few other things on my 88 GT. This may be a dumb question but I cant seem to locate the slave cylinder, if im looking tword the engine would it be the on the right of the bellhousing? Also, Ive put in a new clutch cable and hooked my pedal back up to it, in my manual it states that you must hook the pedal back up to the pushrod,when I took the pedal off I unhooked some electrical device that activated with the pedal and took the nut off. I dont see a pushrod, I simply hooked the cable back to the quadrant and put the pedal on the shaft then secured it with the nut, am I doing somthing wrong? Thanks in advanced for any help
|
![]() |
![]() |
![]() |
#2 |
N-V-ME
Join Date: May 2005
Location: SOUTHFIELD,MICHIGAN
Posts: 155
|
![]() Thats If You Have A Hydrolic Clutch Yours Is Manual You Have It Hooked Up Right............
__________________
88' LX MUSTANG: LINCOLN ROTORS , AIR SUSPENSION FRONT AND REAR, SUBFRAMES, ROLL CAGE, 92' BLOCK, MSD 6AL, ACCEL 8.8 WIRES, ACCEL COIL, EDELBROCK F4B INTAKE (PORTED),2 IN. 4 HOLE SPACERS, HOLLEY 600 CARB.,HOLLEY BLUE FUEL PUMP AN REGULATOR, E 303 (.498 IN. 220 DUR.) CAM, (.535 IN. OF LIFT W/ 1.72 SCORPIN ROLLER ROCKERS), PORTED E7'S, FLOWTECH 1 5/8 LONG TUBE HEADERS, 2 1/2 IN. H PIPE, 2 CHAMBER FLOWMASTERS WITH 3 IN.DUMPS, T-5, 3.73 GEARS, 5 LUG AEROSTAR AXELS, 245-45-17 96' COBRA WHEELS |
![]() |
![]() |
![]() |
#3 |
Domestic Rice really sucks!
Join Date: Apr 2002
Location: KY
Posts: 973
|
![]() That electrical device the neutral safety switch. Your car doesn't have a hydraulic clutch so there is no slave cylinder. Don't pay any attention to that. Just put it back like you took it off, you will be fine. What book is that you are reading anyway?
__________________
The sig says it all. ![]() |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Sep 2005
Posts: 6
|
![]() thats what i figured I just thought since it was an 88 it might be hydraulic, its a haynes manual, is there better reading out there?
|
![]() |
![]() |
![]() |
#5 |
Domestic Rice really sucks!
Join Date: Apr 2002
Location: KY
Posts: 973
|
![]() Way better. Get a Chilton's. They have them at O'Reilly auto parts. IMO, Haynes sucks!!
__________________
The sig says it all. ![]() |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
2000 Clutch or Slave Cylinder Out | rcntn83 | Modular Madness | 3 | 05-14-2004 08:59 AM |
Rocker adjustment | zach0 | Classic Mustangs | 3 | 04-24-2004 12:28 PM |
8 cylinder into a 6 cylinder engine bay....? | EclipseGST303 | Windsor Power | 8 | 10-04-2002 01:57 PM |
8 cylinder into a 6 cylinder engine bay....? | EclipseGST303 | Modular Madness | 1 | 10-02-2002 07:31 PM |
fitting new slave cylinders for convertible top | marton | Windsor Power | 0 | 05-10-2002 08:44 AM |