© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
09-25-2001, 07:45 PM | #1 |
Registered Member
Join Date: Jan 2001
Location: Live music capital of the world, TX
Posts: 324
|
those with pulleys installed - help!
I am in the middle of changing out the pulleys on my car and i'm having some trouble with the crankshaft pulley. I cant seem to get the main crankshaft bolt out without cranking the engine. I can turn it but the crankshaft turns and it just wont come loose. THe instructions say to put it in reverse or 1st gear. I have an AOD but i went ahead and put it in first anyway. no help. Does anybody know what to do? all help is appreciated.
|
09-25-2001, 08:22 PM | #2 |
I'd rather be basketweaving
Join Date: Feb 2000
Location: Indianapolis
Posts: 2,551
|
stop trying to turn that bolt, thats what holds the harmonic balancer on
you need to loosen the 4 bolts that are on the inside perimeter, your kit should have come with 4 new bolts for it and they should loosen before it turns the crank if it still does, put it in park with the rear wheels on the ground, put your emergency brake on too just to be sure also, go ahead and tighten the balancer bolt back up too, if you loosened it much it could be bad, like your balancer falling off ------------------ 88 Notch, B&M Ripper, 3.73's, Ported E7's, Explorer int. w/ ported lower, pulleys, 1.7RR's, BBK headers, off-road H-pipe, flowmasters, subframes, 65mm TB, March ram air ,MSD coil, U/L control arms, 155lph f/p, Crane Adj.FPR, Nitto drag radials, best 1/4--> 13.76@101.4 on a 2.17 60ft |
09-25-2001, 09:42 PM | #3 |
Procharged!
Join Date: May 1999
Location: Hanover, PA
Posts: 1,539
|
Yeah that center balancer bolt gets I believe 85ftlb/tq not sure on those outside bolts but I think it is 25-35ftlbs, my buddy has my book so I can't check them but I think thats right.
------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension, SPEC stage III clutch, Lakewood SFI bell, S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! [b]12.16 @ 113.5, 1.78 60ft..no traction in the 90 degree |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Saleen Pulleys | 96Saleen | Modular Madness | 4 | 01-01-2004 10:41 PM |
Anyone with Pulleys how much did you pay to get them installed if u dont do it urself | 96_4.6 | Modular Madness | 0 | 10-03-2002 03:07 PM |
pulleys | strokerman | Classic Mustangs | 0 | 05-26-2002 07:23 PM |
Pulleys on 94 cobra? | Casper5.0 | Windsor Power | 1 | 03-07-2001 03:20 PM |
FMS Pulleys and Throttle body | Ripper | Modular Madness | 8 | 01-27-2000 02:26 AM |