Linear Mode
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
07-01-2009, 12:42 PM
|
#1 |
|
Registered Member
Join Date: Jul 2009
Posts: 2
|
engine build help
I Build cat engines for a dealer. I'm new to car fuel injection build
Here's what I have, 302 roller block bored .030 Gt-40 heads from 93 lightning E303 cam 1.72 crane rollers Edlebrock performer intake Stock 19lb injectors Flat top forged speed-pro pistons 70mm edelbrock throttle body 70mm MAF My question is on the fuel side, are the 19lb injectors enough? and will the stock vacuum operated fuel regulator work or should I upgrade to a aftermarket adj one. Also does this combo sound OK. I've never built up a fuel injected gas engine , just going off advice from co-workers. Thanks Ernie |
|
|
|
07-24-2009, 06:27 PM
|
#2 |
|
Registered Member
Join Date: Dec 2006
Location: new york
Posts: 482
|
Re: engine build help
yea the 19's should be fine i was running 11.80 with the stock injectors.i had highly ported heads cam intake roller rockers and some nitrous..i would get a aftermarket regulator there only like 100 bucks and u can get a little more out of the 19's.
__________________
347 stroker all forged,arp everything,stud mains w/girdle,7qt pan,full roller, custom cam, aluminum heads swirl valves 5 angle valve job.quick fuel 750,areomotive pump,cobras w/nitto drags,and m/t et drags for the track, ford racing 373 gears,centerforce clutch,tko500,underdrive pulleys,bassani x-pipe,flowmasters ^best et so far 11.6 1.61 60ft coming soon 9sec et's  1992 mustang gt 2001 gmc 1500 4x4 78 century boat 92 skidoo |
|
|
|
|
07-24-2009, 06:34 PM
|
#3 |
|
Registered Member
Join Date: Dec 2006
Location: new york
Posts: 482
|
Re: engine build help
oh yea idk if ur gonna race this but the 1.72 are gonna hurt ur 60ft times alittle,if u spray it u wouldnt notice ..if not u can put 1.6 on
__________________
347 stroker all forged,arp everything,stud mains w/girdle,7qt pan,full roller, custom cam, aluminum heads swirl valves 5 angle valve job.quick fuel 750,areomotive pump,cobras w/nitto drags,and m/t et drags for the track, ford racing 373 gears,centerforce clutch,tko500,underdrive pulleys,bassani x-pipe,flowmasters ^best et so far 11.6 1.61 60ft coming soon 9sec et's 1992 mustang gt 2001 gmc 1500 4x4 78 century boat 92 skidoo |
|
|
|
|
07-24-2009, 06:35 PM
|
#4 |
|
Registered Member
Join Date: Dec 2006
Location: new york
Posts: 482
|
Re: engine build help
one more thing a aftermarket vaccum reg will be fine u will have more tha enuf vaccum with that cam
__________________
347 stroker all forged,arp everything,stud mains w/girdle,7qt pan,full roller, custom cam, aluminum heads swirl valves 5 angle valve job.quick fuel 750,areomotive pump,cobras w/nitto drags,and m/t et drags for the track, ford racing 373 gears,centerforce clutch,tko500,underdrive pulleys,bassani x-pipe,flowmasters ^best et so far 11.6 1.61 60ft coming soon 9sec et's 1992 mustang gt 2001 gmc 1500 4x4 78 century boat 92 skidoo |
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Help me build a engine | pac663 | Windsor Power | 0 | 10-23-2002 07:37 PM |
| New Engine Build Help | Young_Pony | Windsor Power | 2 | 08-22-2002 01:27 PM |
| build me an engine! | BLOCKER | Windsor Power | 5 | 09-17-2001 10:36 PM |
| 302 Engine re-build | robertwesolek | Classic Mustangs | 4 | 08-09-2001 12:45 PM |
| engine carbon build-up | richie | Windsor Power | 3 | 04-21-2001 02:40 PM |