MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Mustang & Ford Tech > Windsor Power
Register FAQ Members List Calendar

Notices


Reply
 
Thread Tools Rate Thread Display Modes
Old 01-15-2006, 09:26 PM   #1
83GTMUSTANG
N-V-ME
 
83GTMUSTANG's Avatar
 
Join Date: May 2005
Location: SOUTHFIELD,MICHIGAN
Posts: 155
Default Stock Sway Bar End Links Length

I Have An 88 Lx And I Wanted To No How Long The Center Piece Is From Washer To Washer Between The Control Arm And Sway Bar Or The Overall Length Thanks In Advance
__________________
88' LX MUSTANG: LINCOLN ROTORS , AIR SUSPENSION FRONT AND REAR, SUBFRAMES, ROLL CAGE, 92' BLOCK, MSD 6AL, ACCEL 8.8 WIRES, ACCEL COIL, EDELBROCK F4B INTAKE (PORTED),2 IN. 4 HOLE SPACERS, HOLLEY 600 CARB.,HOLLEY BLUE FUEL PUMP AN REGULATOR, E 303 (.498 IN. 220 DUR.) CAM, (.535 IN. OF LIFT W/ 1.72 SCORPIN ROLLER ROCKERS), PORTED E7'S, FLOWTECH 1 5/8 LONG TUBE HEADERS, 2 1/2 IN. H PIPE, 2 CHAMBER FLOWMASTERS WITH 3 IN.DUMPS, T-5, 3.73 GEARS, 5 LUG AEROSTAR AXELS, 245-45-17 96' COBRA WHEELS
83GTMUSTANG is offline   Reply With Quote
Old 01-18-2006, 09:57 AM   #2
HoodStrype
Rearview Mirror Haze
 
HoodStrype's Avatar
 
Join Date: May 1999
Location: Huntsville, Alabama...a.k.a. "HuntsVegas"
Posts: 387
Default Re: Stock Sway Bar End Links Length

If you're trying to find end links you just have to measure the width (diameter) of the swaybar itself... that's how they're sold. I've run into that problem recently because my Stang didn't have a front sway bar when I got it. I have yet to buy end links but I've asked and they told me to measure... I think they come in 1 5/8, 1 3/8. Yours being an 83 may be smaller if it is an 83 swaybar... should take any year though I think.
__________________
93 lx Notch
01 GT

...the epitome of Murphy's Law
HoodStrype is offline   Reply With Quote
Old 04-08-2017, 10:09 AM   #3
tim123
Registered Member
 
Join Date: Aug 1999
Location: Cicero, New York
Posts: 79
Default Re: Stock Sway Bar End Links Length

End links. I just ran into this similar/ same issue with a 86 GT. I purchased the blue MOOG end links pn K700432 (thermoplastic) similar to what I took off. TO answer your question I just measured what I took off next to what I haven't put on. Aprox 1+1/4" between. I don't know if it will work out? I have heard that the factory had them too long. However the bar when all is said and done needs to be level, with whatever links you have on. How did your 88 turn out? I am posting this April 2017.

T
tim123 is offline   Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Dont use 1.7 rockers with stock heads? Coupe5oh Windsor Power 10 11-28-2015 12:36 PM
polishing stock parts? scale Windsor Power 24 04-22-2002 11:57 AM
Stock Cam gtsr515 Windsor Power 1 04-03-2002 10:28 PM
Should I buy (used) Front Sway Bar? Gautam Windsor Power 6 01-29-2001 09:34 PM
LT's vs. shorties vs. stock headers jonnyk Windsor Power 9 01-01-2001 11:28 AM


All times are GMT -5. The time now is 10:41 AM.


SEARCH