© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
10-25-2001, 11:03 PM | #1 |
Registered Member
Join Date: Aug 2000
Location: Bountiful, UT
Posts: 91
|
HELP WITH TORQUE BOXS AAAAAHHHHHH
Does anyone know of any places to buy a rebuild kit other then Wild Rides. I have theirs and they don't seem to be working that well. They hold the lower control arms in but I need a rebuild kit that replaces the whole box. Mine are REALLY REALLY bad. Or has anyone welded theirs in and how would you do it. Thanks everyone.
------------------ 89 LX Supercharged DSS 357, 11 lbs Powerdyne, Downs Box intake, ported GT-40x heads, lockwired, Crane Cam 1.6 rockers, Crower cam, Oil cooler, Moroso oil evac kit, Taylor 10mm wires, MAC 70mm T/B, 36lb injectors, Vortech fuel rails, Pro M 80mm Mass air, Vortech T-Rex Fuel pump, 255lph intank pump, K&N, Cobra R radiator MSD6-BTM, Lakewood bellhousing, Tremec Trans, Pro 5.0 shifter, MAC headers and X-pipe, Dynomax race mufflers. Dyno at 519hp to the wheels. And more to come..... |
10-26-2001, 09:47 AM | #2 |
Procharged!
Join Date: May 1999
Location: Hanover, PA
Posts: 1,539
|
Well I make a kit very similar to tht Wild Rides but mine have a extar plate that ties it to the frame on both sides and they are made from Stainless so they will not rust.
If you already have the Wild Rides kit in I would suggest, tap all the seams back together and make sure they are square again and FULLY WELD all thr factory seams and I welded the top plates to the floor board as well (The ones under the rear seat) If your boxes are really trashed and non repairable South Side Machine makes a replacement adjustable torque box, but I have never delt with this so I do not know if it works. I damaged my boxes very bad since I run the SSM which tend to be hard on the boxes, after welding the seams and adding the re-enforcement kit I have never had a single problem. I also welded plate across the bottom so it boxes the arm in a little. You just need to notch it out so that the arm still has room to travel. Wolfe sells similar plates for $25.00. ------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,30#,76mm C&L,75mm Accufab, Full MAC, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension, SPEC stage III clutch, Lakewood SFI bell, S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 33 splines coming very soon! [b]12.16 @ 113.5, 1.78 |
10-26-2001, 01:41 PM | #3 |
Registered Member
Join Date: Apr 2001
Location: Gallatin, Tn
Posts: 1,326
|
Rick, on your website it said you ran 12.60's on another set of rims and tires, on your post it says 12.10's what did you do since what you have on your site to run 5tenths faster? I have a very similar setup and have not run the car yet, so I was curious to how close my times would be to yours, thanks
------------------ 88LX NOTCH 5.0, TFS Twisted Wedge Aluminum heads, 2.02 1.60 valves, BBK shorties unequal 1 5/8, off road H-pipe, Flowmasters, Drag lites, custom grind cam, solid motormounts, Aluminum Driveshaft, BBK springs, lakewood 90/10 50/50 shocks, BBK upper and lower control arms, 4.10 gears, centerforce DF clutch, adjustable BBK clutch cable with aluminum quadrant, Billet Steel flywheel, 70mm Acufab Throttle Body,MAC cold fender mount induction, K&N, 3 core radiator, flex-lite-fan, custom hardened push- |
10-28-2001, 07:20 AM | #4 |
Procharged!
Join Date: May 1999
Location: Hanover, PA
Posts: 1,539
|
USMC302- Check your e-mail...
------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,30#,76mm C&L,75mm Accufab, Full MAC, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension, SPEC stage III clutch, Lakewood SFI bell, S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 33 splines coming very soon! [b]12.16 @ 113.5, 1.78 |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
raced a Supra Twin Turbo | Stang35th | Stang Stories | 63 | 08-23-2003 12:36 AM |
Torque strap. Yes or no | Dark_5.0 | Windsor Power | 3 | 06-05-2003 07:00 AM |
T-5 Torque Rating | sleeperstang | Classic Mustangs | 5 | 07-05-2002 10:54 PM |
T-5 Torque Rating | sleeperstang | Windsor Power | 1 | 06-27-2002 08:18 PM |