![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#21 |
NX dealer-man
Join Date: Sep 1998
Location: Peoria, Illinois
Posts: 977
|
![]() Here's a better example of where the access hole is relative to the trans... I just use a standard allen wrench to make adjustments.
|
![]() |
![]() |
![]() |
#22 |
NX dealer-man
Join Date: Sep 1998
Location: Peoria, Illinois
Posts: 977
|
![]() here's another pic of the assembly apart....
|
![]() |
![]() |
![]() |
#23 |
Founder
Join Date: Jun 1995
Location: Michigan
Posts: 19,326
|
![]() Cool. I am going to start out with just one turn on mine, which should give me ~990 lbs or something like that. But, I'll have 9 grams of counterweights on it also. The counterweights, in my line of thinking, should allow you to use lower base pressure while still allowing it to clamp down hard as the RPM comes up and the additional clamping force comes in from the weights...
How much slippage do you get launching your car before the clutch really clamps in with your current set-up? Oh, and I'll take your Jerico! ![]()
__________________
StangFlyer 1991 Mustang GT - Supercharged 377 Stroker 2000 Ford Lightning - Project Lightning Hauler Media Center Gallery - View my member photos |
![]() |
![]() |
![]() |
#24 | |
NX dealer-man
Join Date: Sep 1998
Location: Peoria, Illinois
Posts: 977
|
![]() Quote:
![]() As for counterweights, I'm not sure how RAM does their kits, but the McLeod unit comes with a pack of steel allen bolts (1"=8g. ea., 3/4"=6g. ea, 1/2"=5g ea.), steel nuts (3.5g. ea.), aluminum hex bolts (1"=3g. ea., 3/4"=2.5g. ea., 1/2"=2g. ea.), aluminum nuts (1g. ea.), and steel barrel weights (3.5g. ea.). Included with this pack is a few pages of info explaining the function of a counterweighted type release lever. You can either add these weights to the inboard or outboard position of the pivot point of the lever, with the outboard position being the one that adds pressure to the clutch. Will you be trying 3 grams on each lever (9g. total) or 9 grams on each lever? Reason I ask it that in the lit. I got with the unit I use there is a note: "C/W can make the car hard to shift at high RPMs due to the tremendous effect it has on weak clutch linkage and also increasing pedal effort. C/W can also make the car push thru the starting line causing a red light. This is because after staging, when you bring the RPMs up, the C/W comes in forcing engagement. For these reasons in manually shifted trans. apps., C/W is added very lightly, if at all. Therefore, to regain lock up during gear changes, slightly increase static pressure only. This will have no effect on staging of the car of during shifts." Hope this helps some.... and no you can't have my Jerico, LOL! ![]() ![]() |
|
![]() |
![]() |
![]() |
#25 |
Founder
Join Date: Jun 1995
Location: Michigan
Posts: 19,326
|
![]() Yeah, 9 grams total. I have the exact same type of bolts and nuts in a pack with mine. I have three aluminum pairs and three brass pairs. I dare say they weigh about the same.
Sounds like you really aren't taking advantage of what this clutch configuration is for yet though. Other than just being able to hold gobs of power/torque, it gives you the ability to use low enough base pressure to allow the clutch to slip during launch (60 ft) enough to let you hook up. Then as RPM's come up it locks-up and 100% is to the wheels. That keeps you from blowing the tires and from killing drivetrain parts. I will personally have to rely on this a lot. With the street set-up my trans will probably live. However, with the race configuration it would most assuredly die a painful death without utilizing this clutch to allow off the line slippage. Unfortunately, I don't have a Jerico and I've got a Tremec TKO behind this beast. Workable for the street config with 100% off the line lockup, but for the race config it's out of it's league. My plan is to adjust mine so that for track duty, it will slip just enough off the line to allow me to hook with the bigger boost, keep my trans alive in the process, but once I'm moving to have 100% lock. Now, actually Mike (owner of RAM) told me some time ago that Cory Roth was running this set-up. Supposedly, he was only using 400 lbs base pressure, but then had the counterweights on also. I'd have to check old emails to find the details.
__________________
StangFlyer 1991 Mustang GT - Supercharged 377 Stroker 2000 Ford Lightning - Project Lightning Hauler Media Center Gallery - View my member photos |
![]() |
![]() |
![]() |
#26 | |
NX dealer-man
Join Date: Sep 1998
Location: Peoria, Illinois
Posts: 977
|
![]() Quote:
![]() Thanks Dan, -Ryan |
|
![]() |
![]() |
![]() |
#27 |
Founder
Join Date: Jun 1995
Location: Michigan
Posts: 19,326
|
![]() Absolutely Ryan. I'll be testing it out as soon as spring gets here and playing with tuning it. I will get this done over the winter finally. In fact, our discussion has actually gotten me a little more excited to go wrench on it again. ahahahaha.
![]() ![]() Btw, you have some good 60 fts there. The best I ever did with my 302 combo was a 1.45, BUT now we're talking a whole different animal with what I have now eh. We'll see how it goes next season...
__________________
StangFlyer 1991 Mustang GT - Supercharged 377 Stroker 2000 Ford Lightning - Project Lightning Hauler Media Center Gallery - View my member photos |
![]() |
![]() |
![]() |
#28 | |
NX dealer-man
Join Date: Sep 1998
Location: Peoria, Illinois
Posts: 977
|
![]() Quote:
![]() ![]() Take care, -Ryan |
|
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
What's a fair price on a explorer intake? | Vishnoff | Windsor Power | 4 | 05-07-2003 01:38 PM |
Speed Secret # 3 | jim_howard_pdx | Windsor Power | 13 | 11-09-2002 10:35 AM |
That iron rod behind the intake... | chris91LX | Windsor Power | 3 | 11-14-2001 07:10 PM |
New!! Intake SPYDER, 302 | Stang Runner | Windsor Power | 1 | 07-15-2001 09:58 PM |
Cold Air Intake Discussion | King Snake | Modular Madness | 7 | 10-13-2000 04:37 PM |