© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
06-08-2002, 05:41 PM | #41 |
Registered Member
Join Date: Sep 1998
Posts: 495
|
Mach 1:
Whatever man, you'll be the first to know when help gets here. |
06-08-2002, 08:08 PM | #42 |
Registered Member
Join Date: May 1999
Location: Georgia
Posts: 3,866
|
Thats ok, you can tell somebody else first, I really dont care
|
06-11-2002, 01:06 PM | #43 |
Registered Member
Join Date: Aug 2000
Location: Wisconsin
Posts: 879
|
would the afr 185's be a good head for a 331?
__________________
'91 GT,410W,10.5 to 1 comp,Victor Jr. heads,Victor 5.8 intake,FTI cam,Crane retro fit lifters,Scorpian 1.6 RR's,Melling HV oil pump,MSD distro.,Canton oil pan,FMS flywheel,Romac balancer,FMS timing chain,Accufab 90mm TB,C&L 76mm maf, 42lbers,HD clutch,K&N air filter,Mac long tubes,Pro dumps,powerchamber,FMS 9mm wires,180 thermostat,Ford Racing gauges,5inch Tach,centerline convo pro's,nitto DR's,Pro3i lower control arms,50/50 shocks,3.55 gears,TFS HD diff. cover Next year: Tremec TKO,Spec stage 3 clutch,alum driveshaft,complete fuel system www.angelfire.com/linux/demondan |
06-11-2002, 02:01 PM | #44 |
Registered Member
Join Date: May 1999
Location: Georgia
Posts: 3,866
|
yes
|
06-11-2002, 11:20 PM | #45 |
Registered Member
Join Date: Jun 2002
Location: Southwest
Posts: 131
|
I do not know how old this thread is,but if I can get a 393-408 with cast crank for the same price as I can get a steel cranked 331-347 I am going to go with the 393-408 combo. If you are a street brawler and you in one of those areas where a guy wants to look under your hood before you race get the 331-347 combo just get plenty of cam and heads so you can rev the piss out of it,might as well take advantage of the ability to rev with cubic inches thrown in
__________________
Deeper,Harder,Faster Stage Deeper Launch Harder Go Faster |
06-11-2002, 11:49 PM | #46 |
Registered Member
Join Date: Aug 2000
Location: Wisconsin
Posts: 879
|
stroked..the guy i was talken to that sells stroker kits said this for a 393
"rotating assembly would be in the $1199 range + rings and bearings. " thats all forged internals also
__________________
'91 GT,410W,10.5 to 1 comp,Victor Jr. heads,Victor 5.8 intake,FTI cam,Crane retro fit lifters,Scorpian 1.6 RR's,Melling HV oil pump,MSD distro.,Canton oil pan,FMS flywheel,Romac balancer,FMS timing chain,Accufab 90mm TB,C&L 76mm maf, 42lbers,HD clutch,K&N air filter,Mac long tubes,Pro dumps,powerchamber,FMS 9mm wires,180 thermostat,Ford Racing gauges,5inch Tach,centerline convo pro's,nitto DR's,Pro3i lower control arms,50/50 shocks,3.55 gears,TFS HD diff. cover Next year: Tremec TKO,Spec stage 3 clutch,alum driveshaft,complete fuel system www.angelfire.com/linux/demondan |
06-11-2002, 11:58 PM | #47 |
Registered Member
Join Date: Jun 2002
Location: Southwest
Posts: 131
|
sounds like a steal to me only $1199? man I would jump on that one
__________________
Deeper,Harder,Faster Stage Deeper Launch Harder Go Faster |
06-13-2002, 06:30 AM | #48 | |
Yay for Chickys
Join Date: Feb 2001
Posts: 1,532
|
Quote:
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Need Throttle Body & Idle Conrol Valve Info | BigBobsL | Windsor Power | 2 | 02-10-2004 01:16 AM |
HELP!! Need INFO! | srv1 | Blue Oval Lounge | 6 | 09-12-2003 09:20 AM |
Info. on old blocks | 89lxinwky | Windsor Power | 3 | 09-19-2002 12:35 AM |
Need some 351 swap info. | fastang | Windsor Power | 4 | 02-05-2002 11:10 AM |
rear diff. info. please | rokdog13 | Blue Oval Lounge | 3 | 02-07-2001 08:39 PM |