© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
01-20-2001, 01:14 PM | #1 |
Guest
Posts: n/a
|
Cam selection, little help?
I plan on running GT-40X heads & a Kenne Bell "Blowzilla" sometime in the near future. My question is which cam to work well with the screw-type blower and that I can use my 1.72RR's with on the new heads without flycutting? Thanx!
------------------ '89 Notch: R134a A/C conversion, 1.72 FMS RR's, Hedman unequal shorties, MAC 2.5" Cat-back, MAC fenderwell cold air kit, pullies, 65mm BBK/Edelbrock TB & EGR spacer, 75MM Pro-M, 190pump, alum. FMS driveshaft, 3.73 gears, MAC "Racer's Choice" shifter, RAM clutch, MAC quadrant & cable, GT-40 intake, 130A Alt., '95 GT Spindles & brakes, & Polished '99 Cobra wheels w/ 245/45/17 rubber. [This message has been edited by 89NB50 (edited 01-20-2001).] |
01-20-2001, 05:43 PM | #2 |
Registered Member
Join Date: Jan 2001
Location: Rochester Hills, MI
Posts: 40
|
Check out www.alternativeauto.com You may find some info on blower cams there, or give them a call...are you going to upgrade you intake as well?
Rob |
01-20-2001, 10:05 PM | #3 |
Registered Member
Join Date: Jun 2000
Location: Belleville Il, USA
Posts: 234
|
your best bet is to call around to some tech companies. make sure you have all your specs laid out(heads, car weight, gear ratio, etc....), and any future plans/goals in mind for the car and then i would go with a custom grind. try comp, crane, isky, and other such companies to see how similar the grinds they come up with are in relation to each other. good luck, nick
------------------ 1990lx coupe, 302, gt40p heads, wolv 1087 cam, 1.7rr's, 65mm tb, 75mm maf, comp box on top of cobra lower, anderson ford pms, full exhaust, drag type susp. and 3.55's. traps 105mph |
01-20-2001, 10:11 PM | #4 |
I'd rather be basketweaving
Join Date: Feb 2000
Location: Indianapolis
Posts: 2,551
|
ohhh so thats what my car would look like with 17's nice lookin, is it also lowered?
------------------ 88 Notchback 5.0, 3.73's, pulleys, BBK headers, off-road H-pipe, flowmasters, subframe connectors, 65mm TB, shift kit, March ram air kit, motorsport wires, MSD coil, upper and lower control arms, 155lph fuel pump, cheap 2800 stall, Crane Adj.FPR, best time- 13.99@99.75, not yet tested times after 1.7RR install |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Optima battery selection | PWR_RYD93 | Windsor Power | 12 | 01-12-2004 01:09 PM |
cam selection | avbcon12 | Windsor Power | 42 | 10-10-2002 08:22 AM |
Intake selection with a 383/408 stroker | Capri306 | Windsor Power | 12 | 05-03-2002 10:12 PM |
Gear Ratio Selection | Green96GT | Modular Madness | 4 | 07-19-2001 11:40 AM |
Gear selection | Grulla | Corner Carvers Delight | 1 | 03-13-2000 09:04 AM |