© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
04-11-2003, 02:44 PM | #1 |
Import Slayer
Join Date: May 1999
Posts: 2,241
|
I need cam advice for a 351w
I'm starting to buy parts for rebuilding my 351w that's in my '82GT
and I am debating what cam specs I will need. This is my combo so far: - Forged flat top pistons(.060) - Edelbrock performer intake - Carter 625 carb. - Mallory electronic distributer - BBK shorty headers w/ flowmaster exhaust Most of the stuff I already have. I just bought the rebuild kit from Summit Racing last night. I'll be runnig a C-4 tranny with a 2000 stall converter. Depending on my cash flow, I will either keep my '69 heads and freshen them up or buy aftermarket heads. It will be street/strip car. I was thinking of Competition Cams 280* with .512 lift int/exh. I want something that will work with what I have but I also want to hear a nice radical idle. I also think about a duel pattern profile from Cran Cams with those similiar specs. What do you guys think? Are those specs in the right ballpark for me? I'm open for suggestions.
__________________
'82 GT 351W (.060)Comp Cams 274* Extreme Energy cam, ported & polished heads w/ 1.94/1.60 valves 10.3:1 flat top pistons,stealth intake, Mallory dizzy,Holley 750dp carb, BBK shorties,Flowmaster exhaust,C-4 with 3700 stall converter, B&M pro shifter,8.8 rear, 4:10's, subframes, electric fan, powermaster alternator, 4 core radiator. |
04-11-2003, 03:47 PM | #2 |
Registered Member
Join Date: Feb 2003
Location: Bradenton, FL
Posts: 4
|
Question
Wondering why you are going .060" over - is that what it took to clean up? I ask because I have a block right now that is not perfect at .040" and the machinest said he would not go bigger on a Ford.
|
04-11-2003, 10:01 PM | #3 |
Import Slayer
Join Date: May 1999
Posts: 2,241
|
Yep, that's what it took. Someone had already rebuilt it in the past and went .030. The machine shop said he tried .040 and it was still "kinda rough" and took it .060
He said that the block is finished after this rebuild because .060 is the very max. You can take yours to .060 too but the cylinder walls are getting thin at that point. Anyhow, I heard .060 is the max.
__________________
'82 GT 351W (.060)Comp Cams 274* Extreme Energy cam, ported & polished heads w/ 1.94/1.60 valves 10.3:1 flat top pistons,stealth intake, Mallory dizzy,Holley 750dp carb, BBK shorties,Flowmaster exhaust,C-4 with 3700 stall converter, B&M pro shifter,8.8 rear, 4:10's, subframes, electric fan, powermaster alternator, 4 core radiator. |
04-12-2003, 12:30 AM | #4 |
Guest
Posts: n/a
|
nervous about the 60 over
I wouldn't have gone that far,the 60 over is pushing it,as the cylinder bores are already thin the way it is,
As far as cam for your combination,the best thing to do,is call some manufacturers and get some reccomendations,if money is no problem,go custom grind. |
04-12-2003, 07:47 PM | #5 |
Registered Member
Join Date: Feb 1999
Location: brooklyn center,mn,USA
Posts: 169
|
the first 351w block i tried to use cut through the cylinder wall at .060 I'd think twice about using a windor block bored more than thirty or forty. I wish ya luck
__________________
88LX notch, Speedpro EFI 358windsor 11.2 to 1 compression, 5 lug baer claws all around..g force t5 and 3.55 gears. rwhp soon to come. Oh yeah...92 octane NO detonation. |
04-12-2003, 10:24 PM | #6 |
Registered Member
Join Date: Feb 1999
Location: Houston,TX
Posts: 466
|
I wouldn't worry about .60 over if it didn't go through then you are fine for a street setup. My street 351 is 60 over and a sleeve in one cylender and a 175 shot on it. It take the beating and asks for more. If you have the money I would get the conversion lifters with the tie bar (those lifters allow you to run any of the roller grinds for the fords not just the small base circle grinds like drilling and tapping to convert it) and run one of the trick flow cams probhaly the stage 2 by what it seams that you are stating.
__________________
A good plan, violently executed now, is better than a perfect plan next week. George S. Patton, General (1885-1945) |
04-15-2003, 11:26 AM | #7 |
The Stang Gang
Join Date: Jan 1999
Location: St. Petersburg
Posts: 63
|
Thats a good choice - I have a similar setup, but I went with the cam one series smaller; I would have liked the 280 for my application thinking back on it.
__________________
°79Stang° • 351w, TRW Flat Tops, Comp Cam 270h,Edelbrock RPM Intake, Holley 750 Duel Feed, MSD-6a, 2,500 stall, Flowmasters, MaC shorties, B&M Shift Kit, Hurst Pro-Matic][, DrAgLiTES on all four's No Times yet - heads on the way |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
351w or 347 stroker? which is better? | BLACK85GT | Windsor Power | 55 | 12-21-2002 06:52 PM |
does anyone have 351w heads on a 302 block need advice | 93calcobra | Windsor Power | 7 | 12-15-2002 03:21 AM |
351W heads on 289 stock engine | sleeperstang | Classic Mustangs | 5 | 11-21-2002 08:35 PM |
Considering the swap to a 351W - need advice | 2FastLX | Windsor Power | 22 | 06-11-2001 06:46 PM |
Building a 351w, advice | dinomite | Windsor Power | 1 | 02-06-2001 03:20 AM |