Granetelli or Mallory fuel pick-ups

GTSteed89 · 01-17-2001, 12:03 AM

There is a major problem. I'm swapping to carb and running 3/8 braided lines, the pickups are 1/2 lines. Does anyone make a reducer for these since the pump I bought has 3/8 lines? Please help!!!

------------------
89GT...stock motor....C4 w/ 10in. 3800 stall, 3.73's, Powertrax, aluminum shaft, all the free stuff, pulleys, torque link, Pro-M, Ram air, 70mmtb, home ported stock 87 upper to home gasket matched on car 89 lower, BBK adj. FPR, full exhaust, Bassani X pipe, Manual rack, MARCH tensioner pulley eliminator alternator bracket, MSD ignition and coil, Welds, 50/50's, sway bar off front, Eibach Drag Launch kit, MAC control arms, 70/30's, subframes welded in, lightened up on McCreary DOT's. Previous b

MiracleMax · 01-17-2001, 12:53 AM

Are they A/N threaded or pipe threaded. Let me see here. Found the GMS site
http://www.granatellimotorsports.com/

Looks to me like they are A/N threaded? If so you'll need an A/N 08 coupler, an 08/06 flare union reducer, and an 06 hose end.

-08 coupler 8.99 (799-4001)
-08/06 reducer 6.99 (799-6177)
-06 Hose end 4.99 (799-1002)

So 21.00 bucks to solve the problem or there abouts. those are Russell fittings and are all straight,and are all Jeg's parts numbers. I think they use a company prefix followed by a manufacturer suffix. So if you have a parts palce close by that has Russell stuff or you have another mail order parts company you deal with then try giving the suffix part number and see what they have.

01-17-2001, 12:03 AM	#1
GTSteed89 Registered Member Join Date: Mar 1999 Location: Leesport, PA USA Posts: 24	Granetelli or Mallory fuel pick-ups There is a major problem. I'm swapping to carb and running 3/8 braided lines, the pickups are 1/2 lines. Does anyone make a reducer for these since the pump I bought has 3/8 lines? Please help!!! ------------------ 89GT...stock motor....C4 w/ 10in. 3800 stall, 3.73's, Powertrax, aluminum shaft, all the free stuff, pulleys, torque link, Pro-M, Ram air, 70mmtb, home ported stock 87 upper to home gasket matched on car 89 lower, BBK adj. FPR, full exhaust, Bassani X pipe, Manual rack, MARCH tensioner pulley eliminator alternator bracket, MSD ignition and coil, Welds, 50/50's, sway bar off front, Eibach Drag Launch kit, MAC control arms, 70/30's, subframes welded in, lightened up on McCreary DOT's. Previous b

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
fuel pressure issues	mustang98gt	Modular Madness	3	07-05-2003 10:43 PM
Fuel Problems...I think	silver_pilate	Windsor Power	15	05-31-2003 08:36 PM
Fuel Pumps...... Pick one???	NitroStanggirl	Classic Mustangs	6	11-17-2002 04:25 PM
89 LX Fuel Problems	Ryan94GT	Small Ponies	0	08-19-2002 09:47 PM
Mallory Fuel pumps any good?????	5.0-man	Windsor Power	1	03-12-2001 11:35 AM

01-17-2001, 12:53 AM	#2
MiracleMax Registered Member Join Date: Apr 1999 Location: Hayes, Va, USA Posts: 798	Are they A/N threaded or pipe threaded. Let me see here. Found the GMS site http://www.granatellimotorsports.com/ Looks to me like they are A/N threaded? If so you'll need an A/N 08 coupler, an 08/06 flare union reducer, and an 06 hose end. -08 coupler 8.99 (799-4001) -08/06 reducer 6.99 (799-6177) -06 Hose end 4.99 (799-1002) So 21.00 bucks to solve the problem or there abouts. those are Russell fittings and are all straight,and are all Jeg's parts numbers. I think they use a company prefix followed by a manufacturer suffix. So if you have a parts palce close by that has Russell stuff or you have another mail order parts company you deal with then try giving the suffix part number and see what they have.