![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Feb 2001
Location: Edmond, OK
Posts: 180
|
![]() If I move the battery to the trunk, will I have any problems with the alternator charging it or any starter problems due to the long cable putting such a drain on it?
Where can I get a battery cable at that is long enough? What is the best way to bolt down the battery in the trunk? |
![]() |
![]() |
![]() |
#2 |
The Dude
Join Date: Feb 2001
Location: Arlington, VA
Posts: 1,262
|
![]() I as well was wondering about this....is there a kit thats reccomended? How hard is it? Are there good instructions on how to do it (where to route cables)?
|
![]() |
![]() |
![]() |
#3 |
GOT TORQUE ????
Join Date: Aug 1999
Location: New Hudson, Michigan, USA
Posts: 689
|
![]() I'm thinking about doing this too. My biggest problem is losing the cargo space back there. I know a battery isn't that big, but when you have all of you junk packed in the car headed up to school it gets pretty tight back there.
I have older power pulleys and I don't get a good charge to begin with. If I could find my damn Electronics book I could give you exact numbers, but I really don't think you'll notice any charging problems. I'm not going to be too worried once I get a stock diameter pulley to put back on. If and when I relocate the battery I'll ask members here and on other boards what kit they've used and how it worked for them. And as usual price will be a factor when choosing a particular kit. I also plan on getting an A/C eliminator kit. ------------------ 1991 GT, AOD, Moroso Cold Air, 3.73s, March pulleys, 3-chamber(the left one fell off-NO time+No Money=College), FMS c-springs, and KYBs |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Feb 2000
Posts: 469
|
![]() I have the cheap summit kit (the one with the cheap plastic case)
Had the same battery in my trunk for 2 years, no charging problems. My cable is ran along the same route as the fuel lines. The cable came with the kit. The kit came with the hardware needed to bolt everything into place and it holds it securely. I have a vert and it takes away some of the trunk space but not too bad...nothing like my nitrous bottle! (I really have NO trunk space and can only fit my convertable top boot and a set of jumper cables back there! |
![]() |
![]() |
![]() |
#5 |
or '331 LX Eric'
Join Date: Jan 1999
Location: Columbus, Ohio
Posts: 2,142
|
![]() Is there a better kit out there - other than the Summitt kit? I plan on doing this in the next couple of weeks so any recommendations would be great. Also, what is the proper gauge of cable to use?
Thanks, E ------------------ 1991 5.0 LX Coupe -37,800 miles 13.17 @ 106.14 mph w/ 2.138 60' Pro-Charger D-1SC on the way!!! |
![]() |
![]() |
![]() |
#6 |
Registered Member
Join Date: Apr 1999
Location: Burbank, IL
Posts: 249
|
![]() I was thinking about buying the summit kit too, but what do you need to do, so you can pass inspection at the track?
|
![]() |
![]() |
![]() |
#7 |
Registered Member
Join Date: Feb 2000
Posts: 469
|
![]() moroso kit is NHRA and IHRA legal, costs 91.95 for the box, and cables are sold seperately for 104.95
summit kit is 42.95 w/cables |
![]() |
![]() |
![]() |
#8 |
Registered Member
Join Date: Apr 1999
Location: Hayes, Va, USA
Posts: 798
|
![]() When you mount your battery in the trunk, be sure and run a ground all the way to the front again. On efi cars, its essential that the computer is grounded properly. If your going to kit bash (buy the box and do your own cables) then go up a gauge or two in cable size. Pro-M's site has a note or two on mounting the battery in the trunk.
|
![]() |
![]() |
![]() |
#9 |
Registered Member
Join Date: Aug 1999
Location: Charlottesville, Va, USA
Posts: 328
|
![]() I bought the Taylor kit for my car it comes with everything you need. Its a nice aluminum box. I paid $110 for mine its a nice kit.
|
![]() |
![]() |
![]() |
#10 |
Registered Member
Join Date: Nov 1998
Location: Portland, OR
Posts: 113
|
![]() I am also planning on doing this. A set of jumper cables will work nicely as battery cables I think (well, not with the clamps of course!)
|
![]() |
![]() |
![]() |
#11 |
Registered Member
Join Date: Jan 2001
Location: san diego, ca
Posts: 17
|
![]() you shouldnt have any charging problems rom moving the bat to the trunk if you do it correctly. ok first you need to use a min of 2 gage cable. 0 gage is beter. you dont need to run a ground from the bat all the way to the front of the car. that just dumb. you do need to run a good ground cable from the bat to the body of the car. the best way to do that is to have a bolt welded to the body in the trunk. then you have to put a ground cable from the block to the body in the engine compartment. a welded bolt works really well hear. a muffler shop sould be able to weld these for you for really cheap. now if you goto nhra sanctioned tracks then you need a nhra approved bat box. if not then you just need to make shrue the bat if firmly secured to the floor of the trunk.
[This message has been edited by n2ojunkie (edited 02-24-2001).] |
![]() |
![]() |
![]() |
#12 |
Registered Member
Join Date: Nov 2000
Location: Milwaukee,Wisconsin
Posts: 380
|
![]() My bud has the Summit kit and has not affected his alternator and starter. He only paid $43 and for that you get everything(neg. and pos. cables, mounting kit, instructions)
|
![]() |
![]() |
![]() |
#13 |
Registered Member
Join Date: Feb 2001
Location: Edmond, OK
Posts: 180
|
![]() I'm going to put it in the back left so that my cable will be shorter. Is that just as good as putting it on the back right of the car?
|
![]() |
![]() |
![]() |
#14 |
Registered Member
Join Date: Nov 1998
Location: Sugarland, TX USA
Posts: 161
|
![]() Here is how I mounted mine. Works great. It is the Summit kit. Be sure to use a large ground wire going to your engine up front too. I have a wire going from my engine to my front sway bar braket.
http://www.fbody.com/members/LarryS/battsetup.jpg ------------------ 88 347, Twisted wedge heads,Comp Cams 224/230 cam, 1/4=10.718 @ 123.02 mph,dyno= =http://www.fbody.com/members/LarryS/mustdyno.jpg |
![]() |
![]() |
![]() |
#15 |
Registered Member
Join Date: Feb 2001
Location: Edmond, OK
Posts: 180
|
![]() Where can I get that type of wire at in bulk?
|
![]() |
![]() |
![]() |
#16 |
Mustang Addict
Join Date: Jan 2001
Location: McKinney, TX
Posts: 1,294
|
![]() Putting it in the back right is best for traction because you are sitting in the front left seat, which takes a little weight off the back right tire.
|
![]() |
![]() |
![]() |
#17 |
Registered Member
Join Date: Feb 2001
Location: Edmond, OK
Posts: 180
|
![]() To those of you that have the battery mounted in the trunk, how did you route the wire back up to the solenoid? Did you run it through the interior or under the car? And if you ran it under the car, how did you fasten it to the underside?
|
![]() |
![]() |
![]() |
#18 |
Registered Member
Join Date: Sep 1999
Location: Vancouver, WA USA
Posts: 439
|
![]() A couple of things...1. In order to be NHRA legal, the hold down rods have to be mounted (welded to) or go thru the frame rails. 2. If you use a dry cell like an Optima or the Interstate Battery equivalent, you don't need a box. You can buy the number 1 cable at any Napa or Thrifty supply house. Easiest under the car along the frame rails with cable tie downs. Take the negative side to the frame rail as well. Do not just bolt it to the body. Not a good ground.
Ron [This message has been edited by Ron1 (edited 03-09-2001).] |
![]() |
![]() |
![]() |
#19 |
Dirk Diggler
Join Date: Feb 1999
Location: SLOATSBURG, NY
Posts: 1,931
|
![]() i ran 1/0 gauge welding cable witch IMHO is the best stuff out there..we have run that gauge wire to a section of body in the back and run cars with no problems..thier is no need to run a ground up front as long as you have a good ground out back..welding cable is supurioir because of 3 main reaons
-1..its extreme flexibality -2..its restance to heat(its made for shorting out) -3..its extreamly conductive(has thousands of little strands of wire in it) ------------------ 1987 black notch(ex 4 banger) DSS 306 w/ main support...Elderbrock 6028 heads..gt-40 intake..24# injectors...70 mm tb..77 pro-m...accel 300+..mac full legnth..tremec w/ pro5oh...full MAC exhaust,off road h-pipe,long tubes, catback...ron davis radiator..subframes, control arms...CFDF II..o yea holley FPR sucks..dont buy one.. AIM=onesillynotch |
![]() |
![]() |
![]() |
#20 |
Guest
Posts: n/a
|
![]() I have a roller right now that was doing 9's. The battery is mounted in the trunk but it's kind of just sitting there. There is a on/off switch next to the parachute that controls the current in the car. It's a pretty cool setup as the line are run along the subframe connectors. I have to order the summit kit to keep it from floppin around
|
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Battery..Solenoid..Starter problem | abesmith69 | Windsor Power | 6 | 04-09-2003 09:39 AM |
Battery not charging | Mustang_289 | Windsor Power | 8 | 01-04-2002 07:07 AM |
Battery Relocation... | Bad89stang | Windsor Power | 1 | 12-01-2001 12:47 PM |
When moving solenoid to the trunk with battery... Help Please | Rick 91GT | Windsor Power | 2 | 04-18-2001 07:51 AM |
battery in the trunk | stroker393 | Windsor Power | 0 | 03-09-2001 07:23 PM |