© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
07-25-2001, 01:48 PM | #1 |
Registered Member
Join Date: Oct 2000
Location: Ontario canada
Posts: 446
|
sfi pressure plates
I'm looking for an inexpensive presurre plate and clutch that meet sfi standards I have a sfi flywheel but at the track they were asking me for my sfi # 's for my pressure plate and clutch and since its time to change it anyway. The only pressure plate advertised as sfi i found is the ram unit but it with their clucth recommends not using slicks . will install a new lakewood sheild at the same time.
thanks any recomendations appreciated. also i guess i will use my t5 with the 351 w . ------------------ 89 with 395 single stage n2o .garret t3. 373's Suspention worked out finnaly . need cage . |
07-25-2001, 02:12 PM | #2 |
Procharged!
Join Date: May 1999
Location: Hanover, PA
Posts: 1,539
|
I personally am going with a SPEC clutch, I am getting the stage III which is good for 650hp. They are SFI approved and the kit including PP, Disc, Throw Out Bearing and pilot tool is $328. You should contact them, tell him Rick sent you.
David Norton-starclutch@mindspring.com 800-828-4379 ------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC exhaust 1-5/8" Long tubes,2-1/2" O.R H-Pipe,2 1/2" cat back, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension,S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! FIRST TIME OUT 12.16@111 WHEELS-UP [This message has been edited by Rick 91GT (edited 07-25-2001).] |
07-26-2001, 06:26 AM | #3 |
Moderator
Join Date: Aug 2000
Location: Milan, OH
Posts: 2,699
|
There's not too many SFI pressure plates in the diaphram style. SPEC is probably the hot ticket lately. Hayes makes one, but I wouldn't put a Hayes in a Yugo. When I was going through things last year, Ram's diaphram wasn't SFI approved since its actually made by Valeo and Ram can't get third party product approved. If you move to a long style pressure plate, you've got more choices such as Ram and McCleod. I put the numbers for everything inside my driver's side door jam so I could provide them to the tech officials on request.
------------------ Jeff Chambers Trophy Stock #3 11.462 Seconds / 117.43 MPH Chambers Racing Team |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Help woth installing groundpounder coilovers with BBK caster camber plates | ciara | Windsor Power | 0 | 01-10-2004 01:08 PM |
Oil Pressure Very low on new setup!!! | Z28EATR | Windsor Power | 17 | 09-16-2003 04:03 PM |
Rising Fuel Pressure with Rising RPM? | StreetStang37 | Windsor Power | 1 | 05-21-2002 03:49 AM |
Please Help...Fuel pressure keeps moving. | Dark_5.0 | Windsor Power | 2 | 04-06-2002 01:31 AM |
fuel pressure and bad injectors??? | wrathchild | Windsor Power | 1 | 10-02-2001 06:40 AM |