MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Mustang & Ford Tech > Windsor Power
Register FAQ Members List Calendar

Notices


Reply
 
Thread Tools Rate Thread Display Modes
Old 11-18-2002, 09:20 AM   #1
NYC1
Registered Member
 
NYC1's Avatar
 
Join Date: Jun 2001
Location: Maryland, USA
Posts: 169
Default What's the difference in "Progressive" vs "Specific" rate lowering springs?

don't laugh!
__________________
94GT 5spd Coupe
1/4 = 13.6@103
60ft = 2.0315 on Michelin Pilots

GT 40 Intake
GT 40Y Aluminum heads
1.7 rockers, BBK Cold air
Fluidyne, BBK long tubes & H-Pipe
65mm TB
Al Driveshaft
Hurst Shifter
Cobra R hood
HPM Subframes
Control Arms

Future mods = Procharger and/or 331/347 Stroker, Turbo?

Rice Haters Club Member #77

FOR SALE:
Strut Tower Brace $30
NYC1 is offline   Reply With Quote
Old 11-18-2002, 09:43 AM   #2
lx5091
Registered Member
 
lx5091's Avatar
 
Join Date: Nov 2001
Location: Fall River, MA
Posts: 467
Default

Progressive rate springs have bigger gaps between the coils at the top and bottom and smaller gaps in the middle. What this does is allow the spring to compress alot in a slight lean or over bumps, but the more force that gets applied to the spring such as a hard corner, the stiffer the spring gets because you start to compress the tighter coils. These are good for someone who is anal about keeping good ride quality, but wants "a little" more performance. This setup allows quicker turn-in than stock, but is still not really considered "quick" turn-in. Turn-in is the immediate controlled RESPONSE during a corner, like if you are going straight and suddenly pull the wheel on an autocross car it will "turn-in" very fast while being accurate and the same speed left turn in a '53 buick the right side of your bumper would scrape the ground, VIRTUALLY having no turn-in.

Specific rate springs have coils which are evenly spaced these provide very fast turn-in, but don't "absorb" as much of the road and unfortunately are a little harsh over even small cracks.

got it? good. Now go get some 650 lb specific rate springs!

kidding, that's just what I bought altough I haven't yet installed them.
__________________
'02 Explorer XLT 4.0L --Nice Vehicle

'97 Saturn SL1--Soon to be ditched for a Ford!
lx5091 is offline   Reply With Quote
Old 11-18-2002, 10:08 AM   #3
NYC1
Registered Member
 
NYC1's Avatar
 
Join Date: Jun 2001
Location: Maryland, USA
Posts: 169
Default

cool, Thanks.
__________________
94GT 5spd Coupe
1/4 = 13.6@103
60ft = 2.0315 on Michelin Pilots

GT 40 Intake
GT 40Y Aluminum heads
1.7 rockers, BBK Cold air
Fluidyne, BBK long tubes & H-Pipe
65mm TB
Al Driveshaft
Hurst Shifter
Cobra R hood
HPM Subframes
Control Arms

Future mods = Procharger and/or 331/347 Stroker, Turbo?

Rice Haters Club Member #77

FOR SALE:
Strut Tower Brace $30
NYC1 is offline   Reply With Quote
Old 11-18-2002, 01:17 PM   #4
Conman
Registered Member
 
Conman's Avatar
 
Join Date: Apr 2002
Location: Kingston, Ontario
Posts: 351
Default

lx5091 did a pretty good job of describing how they are different
this is just a couple points to add in
specific rate springs have one spring rate thoughout the entire spring and a linear response (i.e 650lb/in) so in this case it would take 650 lbs to compress the spring one inch and another 650 lbs to compress it another inch.
Progressive rate springs do not have a linear spring rate. I don't know exactly what the rates are but it may only take 300 lbs to compress the spring the first inch and then as you compress it more you would work up to say 650 lbs per inch.

Progressive springs are better for someone that wants to increase looks and handling a little while maintaining smooth ride qualities.

Specific rate springs are better for someone looking for more performance and better lowering qualities and willing to sacrifice the smooth ride quality a little bit.

The BBK springs I have are specific rate 650 lb/in and I like them. They are not too harsh and I think specific rates are also cheaper.
__________________

'88 lx, Black on Black, check it out here

Spent all my money on school, what a dumb mistake

I'm old enough to know better, but still too young to care.
Conman is offline   Reply With Quote
Old 11-18-2002, 04:45 PM   #5
Tony Frank
Registered Member
 
Tony Frank's Avatar
 
Join Date: Feb 2001
Location: Brooklyn originally, but Grand Rapids now
Posts: 309
Default

the specifics are cheaper, and do all the BBK specifics have 650lb rate?

wondering cause i have them on my car and always wondered what the rate was.
__________________
Grand Valley State University Senior Accounting and Finance Major

1985 Mustang GT 19,000 ORIGINAL miles, E-303 cam, edelbrock performer RPM intake, holley 600 cfm carb, MAC headers, windage tray, 8.8 rear end with 4.10 gears, 4"cowl hood, 5lug conversion, 04 Mach1 wheels.

http://www.mustangworks.com/cgi-bin/moi-display.cgi?1501
Tony Frank is offline   Reply With Quote
Old 11-18-2002, 07:34 PM   #6
Conman
Registered Member
 
Conman's Avatar
 
Join Date: Apr 2002
Location: Kingston, Ontario
Posts: 351
Default

I think they only make one specific rate set for mustangs and they are 650
__________________

'88 lx, Black on Black, check it out here

Spent all my money on school, what a dumb mistake

I'm old enough to know better, but still too young to care.
Conman is offline   Reply With Quote
Old 03-19-2009, 03:57 PM   #7
Coolbluestang
Registered Member
 
Join Date: Mar 2009
Posts: 3
Default Re: What's the difference in "Progressive" vs "Specific" rate lowering springs?

Ok got a quick 2 quick questions. I have Eibach sport line spings on my 2000 mustang GT coupe, and with 2 jl audio w7 in the back which makes the back lower than the front and I basically want it up a little more. The other thing is that I am trying to do my suspension this year so that next year i can do a new engine w/ kenny bell w/ a 2.6 or 2.8 sc. thx.
Coolbluestang is offline   Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
New 4cyl Springs or Lowering Springs? raptor Windsor Power 17 02-25-2004 06:48 PM
stocks springs vs. lowering springs GhettoPop Windsor Power 1 02-12-2004 07:08 PM
specific or progresive rate lowering springs chatcher Windsor Power 3 11-01-2001 01:05 PM
Lowering my '96 - Springs? ncbflo Modular Madness 1 06-30-2001 09:27 AM
Edelbrock/Eibach lowering spring vs. Eibach lowering springs - diff.? green94droptop Windsor Power 1 06-16-2001 02:20 AM


All times are GMT -5. The time now is 06:33 AM.


SEARCH