© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
08-12-2003, 05:31 PM | #1 |
Registered Member
Join Date: Oct 1999
Location: Pierre Part, La. U.S.A.
Posts: 1,850
|
Cam specs
Cam motion said this is what I need.
Duration @ .050 216, lift 531, 114 lobe sep, install @ 112 What do yall think?
__________________
88workcar 1988 Mustang LX 342. 417rwhp @ 6800. 28 X 10 ET Drag, 4.30s, 10.69 @ 126.43 1.42 60ft. 11.13 @ 127.7 on BFGs 1.72 60ft Rice Hater # 42 To be old and wise, You must first be young and stupid I'm somewhere in tthe middle. |
08-12-2003, 10:31 PM | #2 |
Undescribable
Join Date: Sep 1998
Location: Ft Myers Fla
Posts: 1,539
|
Low duration and high lift will probly make alot of torque and be good till around 5500 or so.
__________________
Rice Haters Club Member #101 |
08-13-2003, 06:38 AM | #3 |
Registered Member
Join Date: Oct 1999
Location: Pierre Part, La. U.S.A.
Posts: 1,850
|
I just finished looking in MM&FF in the head test section. The cam used there is very close to the one that cam motion is cutting for me.
__________________
88workcar 1988 Mustang LX 342. 417rwhp @ 6800. 28 X 10 ET Drag, 4.30s, 10.69 @ 126.43 1.42 60ft. 11.13 @ 127.7 on BFGs 1.72 60ft Rice Hater # 42 To be old and wise, You must first be young and stupid I'm somewhere in tthe middle. |
08-13-2003, 07:50 AM | #4 |
Undescribable
Join Date: Sep 1998
Location: Ft Myers Fla
Posts: 1,539
|
got that article right here. seem like with a good set of heads and intake it is making great power. almost 400 with the afr 165's.
__________________
Rice Haters Club Member #101 |
08-13-2003, 09:13 AM | #5 |
Registered Member
Join Date: Apr 2001
Location: Staging lane
Posts: 4,337
|
Can you run that much lift with 2.02 valves and stock pistons?
__________________
92' LX-Big brakes, Lots and lots of suspension, GT40X heads, Ported cobra intake, stock cam, Vortech SC trim. 00' Lightning-Stock 88'CRX-13 second ego killer |
08-14-2003, 06:30 AM | #6 |
Registered Member
Join Date: Oct 1999
Location: Pierre Part, La. U.S.A.
Posts: 1,850
|
I did a clerance check last night.With the E-cam, 100 thou on the exhast, 70 thou on the intake. I can bolt them up and let her rip. Then when the other one comes in I will put it in in a few weeks.
__________________
88workcar 1988 Mustang LX 342. 417rwhp @ 6800. 28 X 10 ET Drag, 4.30s, 10.69 @ 126.43 1.42 60ft. 11.13 @ 127.7 on BFGs 1.72 60ft Rice Hater # 42 To be old and wise, You must first be young and stupid I'm somewhere in tthe middle. |
08-14-2003, 09:47 AM | #7 |
Registered Member
Join Date: Apr 2001
Location: Staging lane
Posts: 4,337
|
Did you use clay to check your piston to vlave clearance?
__________________
92' LX-Big brakes, Lots and lots of suspension, GT40X heads, Ported cobra intake, stock cam, Vortech SC trim. 00' Lightning-Stock 88'CRX-13 second ego killer |
08-14-2003, 12:04 PM | #8 |
Registered Member
Join Date: Oct 1999
Location: Pierre Part, La. U.S.A.
Posts: 1,850
|
Yes clay, and play dough. It came out the same either way.
__________________
88workcar 1988 Mustang LX 342. 417rwhp @ 6800. 28 X 10 ET Drag, 4.30s, 10.69 @ 126.43 1.42 60ft. 11.13 @ 127.7 on BFGs 1.72 60ft Rice Hater # 42 To be old and wise, You must first be young and stupid I'm somewhere in tthe middle. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Aluminum Head Torque Specs | 92MUFDVR | Windsor Power | 5 | 07-24-2003 09:14 AM |
Anyone know a website with 96-98 mustang gt specs??? | 96_4.6 | Blue Oval Lounge | 4 | 03-10-2003 01:23 PM |
Rear Seat Delete Specs??? | 5.0L_Of_Fury | Blue Oval Lounge | 5 | 08-07-2002 12:44 AM |
Question about stock cam specs | MustangGT1990 | Windsor Power | 11 | 04-03-2002 10:04 AM |
CAMBER AND CASTER SPECS FOR LIGHT AUTO X? | LOCASH | Corner Carvers Delight | 2 | 01-06-2001 09:48 PM |