Linear Mode
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
03-04-2003, 07:20 PM
|
#1 |
|
Registered Member
Join Date: Jan 2002
Location: Mt. Prospect,IL
Posts: 474
|
Will 94-95 maf work with foxbody?
will 94-94 maf work on foxbody?
thanks raini
__________________
87-ford-mustang-SOLD! mods: 3:73's, off road h-pipe, b303 cam in gt- 40 motor w/ Power Plus intake, edelbrock 70mm tb & egr spacer, 72mm C&L, bbk long tubes, tremec tranny, centerforce dual friction clutch, upr and lwr CA's 255lph FP and soon more to come.... when i have money again SOME ADVICE Don't do burn outs in reverse it is very expensive New times with dead hook on dr's 13.27@103 with 2.0 60 foots w/100lb system Fastest time to date: 12.8@113 |
|
|
|
03-04-2003, 07:33 PM
|
#2 |
|
motors done......woohooo
Join Date: Mar 2002
Posts: 799
|
the sn95 mass air bolts up with a 4 bolt flange, if you have a cold air you can just cut the flange off, and get a piece of the silicone connector (i think 3") and put it on. you cant use the same rubber piece off of a fox because they have a tapered design
|
|
|
|
|
03-05-2003, 01:16 PM
|
#3 |
|
Registered Member
Join Date: Jan 2002
Location: Mt. Prospect,IL
Posts: 474
|
it will plug in and work fine with the computer though.... right? or wrong?
__________________
87-ford-mustang-SOLD! mods: 3:73's, off road h-pipe, b303 cam in gt- 40 motor w/ Power Plus intake, edelbrock 70mm tb & egr spacer, 72mm C&L, bbk long tubes, tremec tranny, centerforce dual friction clutch, upr and lwr CA's 255lph FP and soon more to come.... when i have money again SOME ADVICE Don't do burn outs in reverse it is very expensive New times with dead hook on dr's 13.27@103 with 2.0 60 foots w/100lb system Fastest time to date: 12.8@113 |
|
|
|
|
03-05-2003, 02:02 PM
|
#4 |
|
motors done......woohooo
Join Date: Mar 2002
Posts: 799
|
i have the sensor from my old fox body in there now and it seems to work fine.
|
|
|
|
|
03-05-2003, 07:57 PM
|
#5 |
|
MW Link Sponsor
Join Date: Sep 2002
Location: rochester , ny
Posts: 79
|
That meter will work perfectly fine .
|
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Axle from 4 banger work? | 90LxDroptop | Windsor Power | 1 | 04-01-2002 08:54 PM |
| will a 91 mass air harness work in a 88 gt? | bryan88gt | Windsor Power | 5 | 03-24-2002 12:39 AM |
| Anyone get ragged on at work for driving a Ford? | Crazy Horse GT | Blue Oval Lounge | 25 | 03-10-2002 07:26 PM |
| will this work for forced induction? | mikos chris | Windsor Power | 0 | 01-14-2001 03:05 PM |
| Need some professional advice - head work, valve springs, rockers, cam. pretty long. | AxemanZZ | Windsor Power | 15 | 01-11-2001 01:30 PM |