Linear Mode
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
05-23-2008, 10:56 AM
|
#1 |
|
Registered Member
Join Date: Apr 2004
Location: Apalachicola, Florida
Posts: 50
|
Starting problem's
I just installed a new cam and timing chain in my car everything went back together great. Started the car and it ran great for a while then it sounded like it was running out of gas. if you give to some gas it sounded like it was hitting on half the cylinders you can take foot off gas and it shuts off now it's not starting at all . I replaced fuel filter and fuel pump with new pump i can hear the pump prime up and there is great fuel pressure at fuel line and there is spark also at plugs there new also.what should i check now I'm running out of ideas.
|
|
|
|
05-28-2008, 07:00 AM
|
#2 |
|
Registered Member
Join Date: Apr 2004
Location: Apalachicola, Florida
Posts: 50
|
Re: Starting problem's
Update. I changed out the ECU and the car started up and is running but my code reader is getting injector out of balance reading. Is that a bad injector?
|
|
|
|
|
06-28-2008, 09:03 PM
|
#3 |
|
Registered Member
Join Date: Dec 2006
Location: new york
Posts: 482
|
Re: Starting problem's
are the injectors all pluged in correctly
__________________
347 stroker all forged,arp everything,stud mains w/girdle,7qt pan,full roller, custom cam, aluminum heads swirl valves 5 angle valve job.quick fuel 750,areomotive pump,cobras w/nitto drags,and m/t et drags for the track, ford racing 373 gears,centerforce clutch,tko500,underdrive pulleys,bassani x-pipe,flowmasters ^best et so far 11.6 1.61 60ft coming soon 9sec et's  1992 mustang gt 2001 gmc 1500 4x4 78 century boat 92 skidoo |
|
|
|
|
06-29-2008, 06:08 AM
|
#4 |
|
Registered Member
Join Date: Apr 2004
Location: Apalachicola, Florida
Posts: 50
|
Re: Starting problem's
Yeah i checked all plugs to injectors also changed injectors with new frp 19lb inj. and still getting the same code after clearing the eec.
|
|
|
|
|
06-30-2008, 06:44 PM
|
#5 |
|
Registered Member
Join Date: Dec 2006
Location: new york
Posts: 482
|
Re: Starting problem's
one quick question what cam are u using?if its not a ford racing cam what are all the specs listed on the cam card ,also what is the firing order printed on the cam card?is the new computer from a 5.0 mustang?did all of your problems start when u installed the cam?
__________________
347 stroker all forged,arp everything,stud mains w/girdle,7qt pan,full roller, custom cam, aluminum heads swirl valves 5 angle valve job.quick fuel 750,areomotive pump,cobras w/nitto drags,and m/t et drags for the track, ford racing 373 gears,centerforce clutch,tko500,underdrive pulleys,bassani x-pipe,flowmasters ^best et so far 11.6 1.61 60ft coming soon 9sec et's 1992 mustang gt 2001 gmc 1500 4x4 78 century boat 92 skidoo |
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| hot starting | af62cobra | Windsor Power | 15 | 10-12-2004 05:20 PM |
| 5.0, now starting..... | knarf | Windsor Power | 0 | 04-29-2004 06:56 AM |
| 5.0 not starting....... | knarf | Windsor Power | 14 | 04-27-2004 09:08 PM |
| Starting out | Tikitoes | Modular Madness | 3 | 04-10-2003 01:53 PM |
| starting up | 1whitesnake99 | Modular Madness | 5 | 01-25-2001 05:53 PM |