Headers and computer 05 stang

cucho · 11-16-2005, 12:30 AM

Hello my friends im the guy from mexico, i just want to know which headers are the best for my 05 gt stang, short ones or long ones, also witch computer is the best, i just put a set of flowmaster mufflers and im gone for the 4.10 rear end gear. Ideas ??? is and automatic.

Jeff Chambers · 11-16-2005, 07:40 AM

There are only two basic computers for the 05GT, CDC3 for the sticks and BKT3 for the autos. The computers are NOT interchangeable due to some of the drive-by-wire programming. If you change the gears, you really need to have a custom program done, again because of some of the underlying program associated with the DBW and torque limitations.

There are quite a few headers on the market, MAC/JBA/Hooker/Dynatech/SHM and more. Just do a little internet research and pick the header that you like best. I'd definitely put a set of Stage 8 locking bolts on at the same time. You only want to have to go after those bolts one time! I've found that the best way to tackle the headers on the 05 is to bite the bullet and drop the k-member. Its the only way to get good access to some of the bolts.

We recently had a 05GT auto in the shop with a Vortech V-2 setup. With a conservative tune, it pushed out 445rwhp at 6200rpm and was still climbing!

11-16-2005, 12:30 AM	#1
cucho Registered Member Join Date: Oct 2003 Location: Mexico Posts: 50	Headers and computer 05 stang Hello my friends im the guy from mexico, i just want to know which headers are the best for my 05 gt stang, short ones or long ones, also witch computer is the best, i just put a set of flowmaster mufflers and im gone for the 4.10 rear end gear. Ideas ??? is and automatic.

11-16-2005, 07:40 AM	#2
Jeff Chambers Moderator Join Date: Aug 2000 Location: Milan, OH Posts: 2,699	Re: Headers and computer 05 stang There are only two basic computers for the 05GT, CDC3 for the sticks and BKT3 for the autos. The computers are NOT interchangeable due to some of the drive-by-wire programming. If you change the gears, you really need to have a custom program done, again because of some of the underlying program associated with the DBW and torque limitations. There are quite a few headers on the market, MAC/JBA/Hooker/Dynatech/SHM and more. Just do a little internet research and pick the header that you like best. I'd definitely put a set of Stage 8 locking bolts on at the same time. You only want to have to go after those bolts one time! I've found that the best way to tackle the headers on the 05 is to bite the bullet and drop the k-member. Its the only way to get good access to some of the bolts. We recently had a 05GT auto in the shop with a Vortech V-2 setup. With a conservative tune, it pushed out 445rwhp at 6200rpm and was still climbing! __________________ Jeff Chambers 1990 Mustang GT 10.032 Seconds / 137.5 MPH 14-time Street Warrior World Record Setter CRT Performance 2001 Tropic Green Mustang GT - 12.181 / 113.2 MPH 2002 Ford F-250 Crew Cab 7.3l Power Stroke - 17.41@77.2 "There's nothing boring about a small block automatic shifting gears at 9400 rpm!"

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
supercharger kit for 03 gt	03GT	Modular Madness	9	05-29-2003 06:38 PM
Tuning the computer?	Mustang Cain	Windsor Power	8	03-08-2002 04:19 PM
A9P computer?? hurting performance??	Smokedawg	Windsor Power	3	07-26-2001 06:14 PM
got harness and mass air meter, which computer?	fiveohpatrol	Windsor Power	1	07-21-2001 04:33 PM
Computer Codes??	Smokedawg	Windsor Power	1	03-29-2001 06:40 PM