© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
|
|
Thread Tools | Rate Thread | Display Modes |
09-04-2001, 12:34 AM | #1 |
Registered Member
Join Date: Nov 2000
Location: Maple Ridge B.C. Canada, The Best Place In The World
Posts: 871
|
SHIFTER OR CAT-BACK???????? Needs Something After My Trip To The 1/4 Mile...
http://www.mustangworks.com/msgboard...ML/002955.html
i ran 16.272@83.11 my car is going to get either a Dynomax Super Turbo Cat Back or a Hurst Or B&M(whichever is better) Shorty Shifter To Help Me Get In The 14s... its my driving that needs improvement, so which will be the best for now??? now which one to get??? ------------------ 1988 Mustang GT, T-5 3.08's, No Smog Pump (Shorty Belt), Dumps At The End Of Stock H-Pipe, K&N Air Filter (Stock Air Box), Removed Air SilencerMy Stang My Site (Not Done Yet) |
09-04-2001, 10:09 AM | #2 |
I'd rather be basketweaving
Join Date: Feb 2000
Location: Indianapolis
Posts: 2,551
|
neither will help you a whole lot, i'd guess the catback would help more but you wont see more than a tenth or so improvement, what you need is more practice and gears
i through a bunch of parts at my car before i had the 3.73s and didnt see hardly any improvement whatsoever, i did read your previous post and im sure that if you get a good run in you could hit low 15s as it sits if you get good traction, get gears/full exhaust/pulleys/ and bump your timing and you MAY hit low 14's/high 13's ------------------ 88 Notch, B&M Ripper, 3.73's, Ported E7's, Explorer int. w/ ported lower, pulleys, 1.7RR's, BBK headers, off-road H-pipe, flowmasters, subframes, 65mm TB, March ram air ,MSD coil, U/L control arms, 155lph f/p, Crane Adj.FPR, Nitto drag radials, best 1/4--> 13.76@101.4 on a 2.17 60ft |
09-04-2001, 11:20 AM | #3 |
Procharged!
Join Date: May 1999
Location: Hanover, PA
Posts: 1,539
|
I actually think the cat back will help you, since you only have dumps at the end of the stock H-Pipe, that motor is seeing no back pressure and will really hurt your performance right now. A nie flowing Cat back and Off road pipe will help. 83mph is very slow even for a stock 5.0 IMHO, I turned 93-95 stock with 2:73 gearing, with the 3:73's I went 104+ on the stock motor. The gears will help also, go 3:73 or 4:10's and get a set of sticky drag tires for the strip.
------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension, SPEC stage III clutch, Lakewood SFI bell, S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! [b]12.16 @ 113.5, 1.78 60ft..no traction in the 90 degree |
09-04-2001, 11:22 AM | #4 |
He said Member...heh, heh
Join Date: Sep 1999
Location: Jupiter, Florida U.S.A.
Posts: 3,718
|
Cat-back for performance and sound!
|
09-04-2001, 06:42 PM | #5 |
Registered Member
Join Date: Sep 2000
Location: Lafayette, Indiana
Posts: 120
|
Looks to me you need to learn how to drive. Then you can worry about buying some parts.
|
09-04-2001, 07:40 PM | #6 |
Registered Member
Join Date: Nov 2000
Location: Maple Ridge B.C. Canada, The Best Place In The World
Posts: 871
|
well, 89 ATI, if you read my thread, you would know that my quadrant snapped out of adjustment while i did a small burnout, so i was shifting with about half clutch.
i ordered the dynomax 2.5" super turbo cat back, and will be getting it in 2 weeks from today (tuesday). i am going to be racing again on friday & saturday to hopefully go low 15s, maby 14s. if anyone knows how to make the stock quadrant not snap out of adjustment, please let me know. ------------------ 1988 Mustang GT, T-5 3.08's, No Smog Pump (Shorty Belt), Dumps At The End Of Stock H-Pipe, K&N Air Filter (Stock Air Box), Removed Air SilencerMy Stang My Site (Not Done Yet) |
09-04-2001, 09:13 PM | #7 |
I'd rather be basketweaving
Join Date: Feb 2000
Location: Indianapolis
Posts: 2,551
|
i know how, get rid of that plastic piece of crap, D&D sells an adjustable cable with an aluminum quadrant for $89, probably would be a great thing to do at this point
------------------ 88 Notch, B&M Ripper, 3.73's, Ported E7's, Explorer int. w/ ported lower, pulleys, 1.7RR's, BBK headers, off-road H-pipe, flowmasters, subframes, 65mm TB, March ram air ,MSD coil, U/L control arms, 155lph f/p, Crane Adj.FPR, Nitto drag radials, best 1/4--> 13.76@101.4 on a 2.17 60ft |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
bought nitros!!! expected 1/4 mile times??? | 1jimmy__d | Windsor Power | 25 | 07-15-2002 08:30 PM |
Pro 5.0 Shifter problem | TomEboi | Modular Madness | 1 | 05-26-2002 09:18 PM |
New 1/4 mile ET from the drag strip!!!!!!!!!! | Fox Body | Blue Oval Lounge | 18 | 03-11-2002 05:22 AM |
Mac shifter install questions | Chevyguy | Windsor Power | 5 | 10-22-2001 03:01 PM |
q/8 mile racing, $15 bucks as many runs as you want!!! | hillie16 | Ford Show & Go | 1 | 09-05-2001 08:39 AM |