Linear Mode
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
01-03-2001, 08:54 PM
|
#1 |
|
Registered Member
Join Date: Jan 1999
Posts: 25
|
Best Cam?
What do you guys think would be the best cam for my setup.89 stock short block,Windsor Jr. heads,1.7 roller rockers,Edelbrock Performer RPM intake,600 cfm carb,March performance pulleys,MSD6-AL,125hp shot of nitrous with a 4-speed tranny.THANX
|
|
|
|
01-04-2001, 03:44 AM
|
#2 |
|
Guest
Posts: n/a
|
If it was ME,I would get a custom ground nitrous cam,you will get the most power going this route.
------------------ [This message has been edited by Mustanguy (edited 01-04-2001).] |
|
|
|
01-04-2001, 12:46 PM
|
#3 |
|
Registered Member
Join Date: Jan 1999
Posts: 25
|
what company would you use for a custom grind?
|
|
|
|
|
01-04-2001, 12:55 PM
|
#4 |
|
Registered Member
Join Date: Apr 2000
Location: middleburg, fl, usa
Posts: 1,134
|
I used comp cams!
------------------ James Cox nochevy@hotmail.com 1991 Mustang LX Best 1/8 time on motor 7.686 @90.20mph |
|
|
|
|
01-04-2001, 01:01 PM
|
#5 |
|
Registered Member
Join Date: May 2000
Location: middleboro,ma, usa
Posts: 734
|
motorsport b cam
|
|
|
|
|
01-04-2001, 01:14 PM
|
#6 |
|
Registered Member
Join Date: Jan 1999
Posts: 25
|
I was looking at either a E-303 or a Crane 2040 what do you think of those cams?
|
|
|
|
|
01-04-2001, 02:03 PM
|
#7 |
|
Registered Member
Join Date: Nov 2000
Location: INDIO CA USA
Posts: 141
|
X-CAM!!! Ilove it!!!!!
------------------ 88 NOTCH DSS 331CI C-4 BRAKE 4:10'S 11.5-1 DART IRON HEADS X-CAM 1.7 ROCKERS 8PT. CAGE BEST 10.9@125MPH 100% STREETALBE TO ME!!! |
|
|
|
|
01-04-2001, 02:36 PM
|
#8 |
|
Registered Member
Join Date: May 2000
Location: middleboro,ma, usa
Posts: 734
|
the 2040 and the e cam are the same thing. and are not designed for use with 1.7 rockers.
|
|
|
|
|
01-04-2001, 09:33 PM
|
#9 |
|
Registered Member
Join Date: Jan 1999
Posts: 25
|
Spinemup,what do you think about the B cam? is it a better cam then the E cam in your opinion?What are some of the advantages of the B cam=====THANX
|
|
|
|
|
01-05-2001, 12:42 PM
|
#10 |
|
DURKA DURKA!!
Join Date: Sep 1997
Location: Lubbock, TX...(TX panhandle)
Posts: 1,418
|
Wolverine 1087, but you'll need valve reliefs in your pistons and preferably and higher compression ratio.
--nathan ------------------ --silver_pilate '91 GT, Built 306, Wolverine 1087 cam, ported Windsor Jr. Irons, and all the goodies...click the link to the left to see a full list of my mods... Tried and True 302 Being Built to Outrun You! heh heh heh... --Texas Panhandle-- Check out my site |
|
|
|
|
01-05-2001, 12:43 PM
|
#11 |
|
DURKA DURKA!!
Join Date: Sep 1997
Location: Lubbock, TX...(TX panhandle)
Posts: 1,418
|
Whoops...sorry, didn't catch that bit about the nitrous....the 1087 probably wouldn't work as well for you.
--nathan |
|
|
|
 |
|
|