![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Apr 2004
Location: Garland, TX
Posts: 9
|
![]() I have aquired a Ford tranny, but do not know what it is. I do know that it is a 4 spd and the numbers on the side are:
C-2604194 RF-D9BR-7006-AB 2 Questions: 1. What model is it? 2. I am planning on connecting it to a 351W, will it work ok? Thanks More Info: Thru some additional searching I think this is a T170FS also known as SROD. Here is a link to the article I found. SROD Description Any help appreciated. Last edited by harleydude; 05-02-2004 at 11:50 PM.. |
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Apr 2004
Location: Garland, TX
Posts: 9
|
![]() Forgive me is my questions seem a bit on the dumb side, but I am trying to absorb as much information as I can from the board and other resources. I have a fair amount of knowledge of working on engines, but do not know the ins and outs of the engine/tranny swaps and combinations that will fit and not fit.
Assuming for the moment that I am going to put the above mentioned tranny in the car, how do I go about finding the right clutch parts? As mentioned before the engine is a 351W. When I am looking for cluth parts do I look for parts that coorespond to the engine year and size or that match the tranny? Also what parts do I need to obtain, so far I think I need Pressure Plate Clutch Disk Flywheel (11" 28oz balance) Clutch fork Clutch cable Anything else??? |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Jun 2003
Location: Wisconsin
Posts: 348
|
![]() throwout bearing, pilot bearing. Was the car manual to begin with, what car?
__________________
92 Mustang GT, 347 Stroker(Forged Steel Crank/Rods-Balanced, Forged Aluminum Dished Pistons), Trick Flow Track Heat Intake, Trick Flow Twisted Wedge Heads w/ Stage 3 port/polish, 80mm C&L MAF, FMS 30# Inj., BBK AFPR, Trick Flow Stage 2 Cam, Trick Flow 1.6R Rockers, BBK E.L. Headers, Flowmaster Cat-Back, MAC CAI, FMS Pulleys, Griffin Alum. Radiator, MSD Pro-Billet Distributor; AOD, Dynamic 3300 Lockup Converter, B & M Super Cooler, B&M Ratchet Shifter; 3:73 gears. |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Apr 2004
Location: Garland, TX
Posts: 9
|
![]() Thanks for the additional info. Forgot about the bearings.
Originally it had a 4 Cyl with a manual transmission. Previous owner removed engine and tranny and replaced with a 351W and an automatic. The tranny is now burned up. I want to put the 4 speed in to get it mobile until I can afford a better tranny. |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
tranny swap? | 03stangGT | Modular Madness | 7 | 11-19-2006 08:57 AM |
Anyone running a C-4 tranny I need HELP!!!!!!!! | mattcstang | Racer's Club House | 5 | 09-07-2006 11:43 PM |
Yet another tranny fluid ?? | Simi Stang | Windsor Power | 4 | 09-30-2003 12:44 PM |
Tranny update...Lentech VB | silver_pilate | Blue Oval Lounge | 10 | 05-02-2002 12:34 PM |
This is bad! Did my Uncle cause my Racing tranny to overheat?(It's a long 1... sorry) | Stang_ROTY | Windsor Power | 1 | 08-30-2001 10:55 PM |