![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Sep 2002
Location: IL
Posts: 105
|
![]() Hey my car just got done and i took it out and it is sluggish, i mean it badly needs to be timed and it just wont move, i floor it and it is like a four banger! any suggestions or could it be the timing?? thanks!
__________________
89' GT with 5spd Hurst short throw, Keith Black 12:1 comp. pistons, Sealed Power drag racing rings, Fms F303 Cam, Ported and polished upper and lower intake with Ported E7TE heads that contain comp. cam double coiled springs with titainum locks and steel retainers, Fel-Pro Head Gaskets, 9mm ford racing wires, BBK chrome unequal shortys, Power Throttle bodies 70mm, Edlebrock 70mm EGR plate, 15inch K&N, Bassani X-pipe, Flowmaster 40 series, Eibach 1 1/2 lowering springs, Cobra R rims 17X9 with p235 on front and p275 on rear with Falken Zeix tires-RUNNING! |
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Jan 2003
Location: Palm Bay, FL
Posts: 432
|
![]() If you haven't checked the timing, I wouldn't rule that out. These things need an assload of timing...10 degrees of base advance just to run normal. Never seen a V8 use so much timing stock.
__________________
'91 Mustang GT 5.0 AOD Daily Driver Current stats: NEW 302 short block, E-303 cam (@.050, 220/220, .498/.498, 110 degrees), 1.6 roller rockers, Performer RPM heads (aluminum, 1.9/1.6, 60cc chambers), Cobra intake, Granatelli 75mm MAF, Billet AFPR, Equal-Length Shorty Headers, Off-Road X Pipe, Flowmasters, 4.10 POSI 13.73 at 103.8, ~2.2 60' |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Sep 2002
Location: IL
Posts: 105
|
![]() Ok yea the timing could be and issue but my car is in my signature and it has the 19lb injectors and i think it needs more fuel or could it also be something with vaccume or the computers because i didnt erase the computers or do anything to them? -Thanks!
__________________
89' GT with 5spd Hurst short throw, Keith Black 12:1 comp. pistons, Sealed Power drag racing rings, Fms F303 Cam, Ported and polished upper and lower intake with Ported E7TE heads that contain comp. cam double coiled springs with titainum locks and steel retainers, Fel-Pro Head Gaskets, 9mm ford racing wires, BBK chrome unequal shortys, Power Throttle bodies 70mm, Edlebrock 70mm EGR plate, 15inch K&N, Bassani X-pipe, Flowmaster 40 series, Eibach 1 1/2 lowering springs, Cobra R rims 17X9 with p235 on front and p275 on rear with Falken Zeix tires-RUNNING! |
![]() |
![]() |
![]() |
#4 |
I'd rather be basketweaving
Join Date: Feb 2000
Location: Indianapolis
Posts: 2,551
|
![]() I will almost guarantee that your timing is just off. Be sure to remember to pull the spout connector while setting the timing. Set it to around 14deg btdc and then plug the spout back in.
Wrong timing will make it run like total crap. Oh yeah, and you are completely fine with 19lb injectors. Until you slap a new set of heads on the car, stick with the 19s. And if anyone tells you that you need 24s, then you need to kick them straight in the nuts. set the timing and let us know what happens
__________________
NMRA O/C 9516 NA pumpgas stickshift 347 10.65@125.6, 6.73@100, 1.41 60ft |
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: Jan 2003
Location: Palm Bay, FL
Posts: 432
|
![]() Doubt there's any issues with the computer.... Not that would make you run like that anyways. Although, from personal experience, I can tell you to reset the computer any time you change ANY sensors. Computers are very sensitive to such things and in my experience, it seems sometimes they have a hard time adapting to a new sensor after they're used to the original. I reset my computer EVERY TIME I replace ANY sensor... I just do it the cheapo, easy way...kill power to the battery. Fair warning though...you gotta drive it around at various rpms a little bit and floor it a few times before the computer learns the right way. First few floorings it'll probably be very slow.
Have you replaced your prom chip? That's not gonna be a problem at your level of modification, but I'd say you've got enough done that you could see some extra power out of a new one.
__________________
'91 Mustang GT 5.0 AOD Daily Driver Current stats: NEW 302 short block, E-303 cam (@.050, 220/220, .498/.498, 110 degrees), 1.6 roller rockers, Performer RPM heads (aluminum, 1.9/1.6, 60cc chambers), Cobra intake, Granatelli 75mm MAF, Billet AFPR, Equal-Length Shorty Headers, Off-Road X Pipe, Flowmasters, 4.10 POSI 13.73 at 103.8, ~2.2 60' |
![]() |
![]() |
![]() |
#6 |
Registered Member
Join Date: Sep 2002
Location: IL
Posts: 105
|
![]() Yea i think that the timing would throw it off alot and since the people at the shops that set the timing before put a bunch of marks on the crank that i cant figure our what ones to use and it is too hard to try and find the right one. The computer has kind of been reset becuase the bat. was disconected for weeks and it was slow as **** when i floored it a buch of times and i just pulled it in becuase it counded so horrible. Well i am going to the shop and hopefully they can time it better than what i timed it, but what else should i tell them to look for?? any info or ideas at all would help! THANKS!
__________________
89' GT with 5spd Hurst short throw, Keith Black 12:1 comp. pistons, Sealed Power drag racing rings, Fms F303 Cam, Ported and polished upper and lower intake with Ported E7TE heads that contain comp. cam double coiled springs with titainum locks and steel retainers, Fel-Pro Head Gaskets, 9mm ford racing wires, BBK chrome unequal shortys, Power Throttle bodies 70mm, Edlebrock 70mm EGR plate, 15inch K&N, Bassani X-pipe, Flowmaster 40 series, Eibach 1 1/2 lowering springs, Cobra R rims 17X9 with p235 on front and p275 on rear with Falken Zeix tires-RUNNING! |
![]() |
![]() |
![]() |
#7 |
Registered Member
Join Date: Jan 2003
Location: Palm Bay, FL
Posts: 432
|
![]() Other than the timing....faulty sensors can cause a car to act up too....IAC, TPS, etc. And more obvious things like a weak ignition. So you can't tell what the marks are on the balancer? I had a hard time reading mine on the factory balancer too...cleaned it up and I was just barely able to read what was etched in there.....a new balancer will fix that right up, but talk about a pain in the ***....lol...
__________________
'91 Mustang GT 5.0 AOD Daily Driver Current stats: NEW 302 short block, E-303 cam (@.050, 220/220, .498/.498, 110 degrees), 1.6 roller rockers, Performer RPM heads (aluminum, 1.9/1.6, 60cc chambers), Cobra intake, Granatelli 75mm MAF, Billet AFPR, Equal-Length Shorty Headers, Off-Road X Pipe, Flowmasters, 4.10 POSI 13.73 at 103.8, ~2.2 60' |
![]() |
![]() |
![]() |
#8 | |
Junior Member
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
|
![]() Quote:
Take care, ~Chris
__________________
Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local
RED & WHITE! |
|
![]() |
![]() |
![]() |
#9 | |
Junior Member
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
|
![]() Quote:
Take care, ~Chris
__________________
Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local
RED & WHITE! |
|
![]() |
![]() |
![]() |
#10 |
Registered Member
Join Date: Sep 2002
Location: IL
Posts: 105
|
![]() Yea the timing was a little off when i took it to the shop and the spark plugs i put in were fouled out and now it runs ok and they took the TPS and reset it to the stock voltage and now they are adjusting the rocker arms becuase i didnt really have to tool to turn over the crank and it just is a pain in the *****. Thanks for the ideas!
![]()
__________________
89' GT with 5spd Hurst short throw, Keith Black 12:1 comp. pistons, Sealed Power drag racing rings, Fms F303 Cam, Ported and polished upper and lower intake with Ported E7TE heads that contain comp. cam double coiled springs with titainum locks and steel retainers, Fel-Pro Head Gaskets, 9mm ford racing wires, BBK chrome unequal shortys, Power Throttle bodies 70mm, Edlebrock 70mm EGR plate, 15inch K&N, Bassani X-pipe, Flowmaster 40 series, Eibach 1 1/2 lowering springs, Cobra R rims 17X9 with p235 on front and p275 on rear with Falken Zeix tires-RUNNING! |
![]() |
![]() |
![]() |
#11 |
Registered Member
Join Date: Jan 2003
Location: Palm Bay, FL
Posts: 432
|
![]() Make sure to post how she runs when all of that is done... Sounds like a sweet setup ya got there...
And PKR...jesus! I guess I'm used to SB Chevy's still... A 305 runs 6 degrees base advance.
__________________
'91 Mustang GT 5.0 AOD Daily Driver Current stats: NEW 302 short block, E-303 cam (@.050, 220/220, .498/.498, 110 degrees), 1.6 roller rockers, Performer RPM heads (aluminum, 1.9/1.6, 60cc chambers), Cobra intake, Granatelli 75mm MAF, Billet AFPR, Equal-Length Shorty Headers, Off-Road X Pipe, Flowmasters, 4.10 POSI 13.73 at 103.8, ~2.2 60' |
![]() |
![]() |
![]() |
#12 |
Junior Member
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
|
![]() The 403 is a wolf in sheeps clothing. Unfortunately, they only made them for three years. I got 521hp out of one of the 403's I had, on pump gas.
![]() ![]() Take care, ~Chris
__________________
Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local
RED & WHITE! |
![]() |
![]() |
![]() |
#13 |
Registered Member
Join Date: Jan 2003
Location: Palm Bay, FL
Posts: 432
|
![]() ![]() ![]() ![]() ![]() Wowsa.
__________________
'91 Mustang GT 5.0 AOD Daily Driver Current stats: NEW 302 short block, E-303 cam (@.050, 220/220, .498/.498, 110 degrees), 1.6 roller rockers, Performer RPM heads (aluminum, 1.9/1.6, 60cc chambers), Cobra intake, Granatelli 75mm MAF, Billet AFPR, Equal-Length Shorty Headers, Off-Road X Pipe, Flowmasters, 4.10 POSI 13.73 at 103.8, ~2.2 60' |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
sluggish deceleration w/ manual trans | thomash85715 | Small Ponies | 3 | 05-04-2004 04:01 PM |
96 cobra feels sluggish | fiveOguy20 | Modular Madness | 21 | 11-09-2003 03:42 AM |
New Exhaust making 98 GT sluggish | SteveGT | Modular Madness | 3 | 05-22-2002 08:51 AM |