© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
02-22-2001, 04:49 PM | #1 |
Registered Member
Join Date: Oct 1998
Location: Dallas, TX
Posts: 261
|
Smog pump seezed on me!
Now I have the initiative to get rid of the pump, so what size belt do i need and what are my options on pluging up all holes (i.e. my offroad h-pipe, and pipes that go behind my heads)?
Thanks, Leo ------------------ 1990GT 5.0 302, T-5, 3.73's, K&n Air filter, Dynomax Super Turbo Exhaust, Hypertech Chip, MSD 6A Ignition, RAM Clutch, Motorsport 3 core, Offroad H-pipe. |
02-22-2001, 04:59 PM | #2 |
Registered Member
Join Date: Oct 1999
Location: New Mexico
Posts: 488
|
Leo, mine seized up on me on vacation last year of all places. Then this past month that new one went bad too. I'd thought about doing the same thing you are talking about by bypassing it, but a new pump only cost me $36 from Autozone. I looked in to a delete kit and it was like $79. I'm not sure what size belt you would need to bypass it completely, but I would think that you could just leave the old pump on and not worry about plugging any holes. Not sure though.
Chris |
02-22-2001, 09:33 PM | #3 |
Registered Member
Join Date: Mar 1999
Location: Vaughn,Ontario,Canada
Posts: 23
|
The same thing happened to me, so what I did was gut it out. Where I live it is not unusual for a cop to pull you over and ask you to lift up your hood. So to avoid tickets I gutted it, so now its basically just a pulley spinning and I can use the stock belt size.
------------------ 1985 Mustang GT Cobra Mostly stock. Flowtech 1 5/8" lontubes, flowtech h-pipe, Flowmaster two chambers, Mac 2.5" tailpipes, MSD-6AL with Blaster coil, Weiand Stealth intake, Eibach springs, Monroe Formula GP's. |
02-23-2001, 10:51 AM | #4 |
Registered Member
Join Date: Oct 1998
Location: Dallas, TX
Posts: 261
|
Well, I thought about hollowing it out but f#ck it, its just added weight. So back to my original question... does anyone know what belt size I will need?? I will eventually be getting pullies so I will need a very tight fit.
Thanks, leo ------------------ 1990GT 5.0 302, T-5, 3.73's, K&n Air filter, Dynomax Super Turbo Exhaust, Hypertech Chip, MSD 6A Ignition, RAM Clutch, Motorsport 3 core, Offroad H-pipe. |
02-23-2001, 06:11 PM | #5 |
Registered Member
Join Date: Sep 2000
Location: Fresno,CA. USA
Posts: 384
|
You can just crimp the end of the pipe going to the h-pipe and weld it to seal.
The y-pipe(on back of heads) can be plugged w/ the thermactor plugs from ford....$5/for the pair Or cut the ends off the pipe, flip them around, and end-for-end them. I relocated my power steering to where the a/c used to be, so my belt size would be different...but if you want that size e-mail me. ------------------ 4.10's,long tubes & 75 shot...Goes 12.50's Check it out at http://www.burnouts.webprovider.com |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
smog pump delete | 89droptop | Windsor Power | 11 | 03-15-2010 04:01 PM |
Smog Pump Deletion | 92MUFDVR | Windsor Power | 7 | 07-14-2003 11:05 AM |
Smog Pump Confusion | Evil Joe | Windsor Power | 1 | 03-23-2003 08:04 AM |
PLEASE HELP!! Do I need the smog pump system to pass dyno emissions ?? | Stang_ROTY | Windsor Power | 5 | 07-02-2001 01:09 AM |
Cats but No Smog Pump | KobraLX | Windsor Power | 11 | 03-20-2001 09:30 AM |