![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
RICE taste like Chicken
Join Date: Jun 2000
Location: Edmond, OK
Posts: 687
|
![]() Ok, I have been debating on what to get for heads...AFR's or TW's. Since I have had NO problems in the past with the TFS heads, and that they are $300 cheaper, I decided to go with them again. That allowed me to get new RR's and a new TB instead of just getting a set of AFR's. Also because the TW's are like the half-way head between the 165, and 185 AFR's with a 170 cc volume, and a 255/195 cfm @ .500 flow rate.
I also bought a set of Crane 1.6 RR's, and a BBK 70 mm tb. I also still have my TFS Intake off of my old car. Luck I guess, the guy didn't want it, he thought it was ugly, so I put my "old" performer on it for him. This leads me to deciding on a cam now. I have the B303 in it now, but my friend has a slightly used E-cam that I might swap out, since I will be tearing down the motor. I am curious to see what this will dyno, after I do this swap. It dynoed 261 with the mods in my sig, so I HOPE 300 rwhp is capable. N-E-wayz, I will hopefully have my new heads and cam on by late tonight,early tomorrow, so I think I will take it to the dyno again on saturday since I will be venturing to Dallas to break in the new pieces. I think there is definately a calling to those 248's. ------------------ Dustin 1993 Cobra #1926 Bassani Full lengths,Bassani short X-pipe, American thunder Cat back, 3.55's. More to come... [This message has been edited by SaleenGTS (edited 02-22-2001).] |
![]() |
![]() |
![]() |
#2 |
I need 110mph Trap Speed!
Join Date: Feb 1999
Location: So, CA
Posts: 4,315
|
![]() I thought that you kept the TFS heads off your old car before you sold it?
Anyways, thats going to be very interesting to see the difference on the dyno. I'm anxious already. Id like to see a 65mm to 70mm TB comarison too. ![]() And I may have a friend interested in those GT40's if u want to sell em. Skyler ------------------ -1989 Saleen Mustang #406- TFS Heads, E-303 Cam, Edelbrock Intake, and a whole lot more. 13.2@106mph -Shooting for 12's and a 351 slowly in the works! Stock-94 Integra 15.48@91mph |
![]() |
![]() |
![]() |
#3 |
RICE taste like Chicken
Join Date: Jun 2000
Location: Edmond, OK
Posts: 687
|
![]() Sky, I ended up selling them to the guy who bought my car. About the heads, I already have a buyer, sorry that was part of the reason I bought the new ones, he wanted those.
|
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Mar 1999
Location: University of Illinois-Urbana/Champaign
Posts: 370
|
![]() Good luck on your new setup. I am also anxious to see what the difference is...i just changed to a 75mm TB and a RPM intake from my TFS heat intake and a 65mm TB...I am waiting to see how much i gain...or lose!! Let us know the results.
------------------ TW Heads, Edlebrock RPM, 75mm TB, 75mm MM, Anderson N-2 cam, stock block, underdrives, paxton regulator, bbk 155 intank, 30lbers, motorsport alum rad msd ignition and coil, 3.73 gear, Tremec 3550, Motorsport HD clutch, K&N, hooker shorties, pacesetter h-pipe, and dynomax cat back, mac upper and lower control arms, no front sway bar. I think that's it. GO ILLINI!!! Waiting for good weather for new times. |
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: Dec 1999
Location: Warrington, PA
Posts: 694
|
![]() MM&FF tested the difference between a 65mm and 70mm TB on a 5.0 w/ the Edelbrock package (heads, intake, and cam) and there wasn't a HP difference between the two. They were absolutely the same.
|
![]() |
![]() |
![]() |
#6 |
RICE taste like Chicken
Join Date: Jun 2000
Location: Edmond, OK
Posts: 687
|
![]() INTERESTING NEWS!!!
Well, after getting my heads and Intake off, I noticed that the heads were ported, and matched to the lower Intake...NO WONDER I HAD 260 RWHP!!! N-E-ways, I have the TW's on, and the cam in, I just ran out of time to get my Intake back on. Yeah the 70 and 65 are virtually the same, but I went with the 70 because I am investing in either a blower or a stroker soon. ------------------ Dustin 1993 Cobra #1926 Bassani Full lengths,Bassani short X-pipe, American thunder Cat back, 3.55's. More to come... |
![]() |
![]() |
![]() |
#7 |
Registered Member
Join Date: Aug 2000
Location: Wisconsin
Posts: 879
|
![]() the main reason i think id go with AFR heads is cause i dont want to mess around with porting...i just wont the best heads possible out of the box.....
------------------ 1991 GT,T-5,air silencer removed,racing clutch(previous owner put in so dont know what kind),K&N air filter,Aiwa deck,power acoustic amp,2 12" pianeers,UPDATE: Just got my Mac long tube headers and Cat-back Future Mods:3.73's,Pro 5.0,Shifter knob,FMS 9mm wires |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
"I BOUGHT AN ABUSE VICTIM"!!! | Dark_5.0 | Blue Oval Lounge | 26 | 03-24-2005 02:39 AM |
bought stang # 3, im addicted. lol | Crazy Horse GT | Blue Oval Lounge | 22 | 08-05-2003 10:45 PM |
Bought a product from the Dark Side! | fiveohpatrol | Blue Oval Lounge | 16 | 07-07-2002 04:50 PM |
just bought first stang, need help, dont know much about this stuff | od0g1742 | Windsor Power | 11 | 10-15-2001 04:00 PM |
i started laughing | RAGE_5.0 | Blue Oval Lounge | 22 | 08-01-2001 05:56 PM |