swapping brake lines to a 8.8

glxstang · 08-10-2001, 08:06 AM

When swapping the brake lines from a 7.5 to a 8.8 axel, what do I do with that little brake line diversion block on the passenger side of the 7.5 axel. If I move it over to the 8.8 will this be in the way when converting to a true dual exhaust?

Thanks.....

Phantom5oh · 08-10-2001, 11:20 AM

You can safely move that over. I have true duals on mine and it has enough clearance. Mine is an '83 GLX.

Phanom

------------------
CHECK OUT MY MODS

http://www.mustangworks.com/cgi-bin/...splay.cgi?1350

red82gt · 08-10-2001, 01:47 PM

Mine clears my MAC tailpipes, I just bouight some heat shielding sleeves and covered the lines to make sure the tailpipe doesn't burn it.

------------------
GT-40 heads (ported, polished, + milled), B303 cam, 1.7rr's, JE pistons, Offy intake, Carter AFB 625cfm carb, Flowtech 1 5/8" shortys, Flowtech X-pipe, MAC Flowpath exhaust, MAC pulleys, 373's, subframes, Eibachs+Tokicos, B&M ripper, FMS Clutch, Zoom Quadrant+cable, 17" CSA Ultra rims, 235/45ZR17 Yokohama AVS S4's, MSD 6A ignition+coil, FMS 9mm wires, Carbed, Naturally Aspirated, and Nasty!

08-10-2001, 08:06 AM	#1
glxstang Registered Member Join Date: Feb 2001 Location: Delray Beach, Florida Posts: 97	swapping brake lines to a 8.8 When swapping the brake lines from a 7.5 to a 8.8 axel, what do I do with that little brake line diversion block on the passenger side of the 7.5 axel. If I move it over to the 8.8 will this be in the way when converting to a true dual exhaust? Thanks.....

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
brake lines, help!	mustangman65_79	Windsor Power	10	06-30-2002 10:37 PM
Stainless steel braided brake lines	Radon	Windsor Power	20	03-24-2002 01:08 AM
Disk Brake Coversion - bending brake lines	glxstang	Windsor Power	1	11-03-2001 11:23 PM
Flaring Brake Lines	glxstang	Windsor Power	3	10-28-2001 11:51 AM
SS front brake lines for M2300K	drudis	Corner Carvers Delight	1	04-11-2001 12:57 PM

08-10-2001, 11:20 AM	#2
Phantom5oh Registered Member Join Date: Mar 2000 Location: Boston, MA Posts: 334	You can safely move that over. I have true duals on mine and it has enough clearance. Mine is an '83 GLX. Phanom ------------------ CHECK OUT MY MODS http://www.mustangworks.com/cgi-bin/...splay.cgi?1350

08-10-2001, 01:47 PM	#3
red82gt Sober voice of Reason Join Date: Nov 1998 Location: Kelowna, B.C., Canada Posts: 1,514	Mine clears my MAC tailpipes, I just bouight some heat shielding sleeves and covered the lines to make sure the tailpipe doesn't burn it. ------------------ GT-40 heads (ported, polished, + milled), B303 cam, 1.7rr's, JE pistons, Offy intake, Carter AFB 625cfm carb, Flowtech 1 5/8" shortys, Flowtech X-pipe, MAC Flowpath exhaust, MAC pulleys, 373's, subframes, Eibachs+Tokicos, B&M ripper, FMS Clutch, Zoom Quadrant+cable, 17" CSA Ultra rims, 235/45ZR17 Yokohama AVS S4's, MSD 6A ignition+coil, FMS 9mm wires, Carbed, Naturally Aspirated, and Nasty!