Oil Pans

dherrer1 · 01-10-2001, 05:28 PM

I have a 1993 GT 5.0. I am doing a number of modifications and one is to upgrade the oil pump and oil pan. I have purchased a Moroso oil pan pant number MOR-20511 and when I received it I noticed it does not have the plug to re-install the low oil level sensor. Did I order the wrong oil pan or do I need to modify it? Has anyone crossed this bridge before? By the way, I am also installing the FMS high volume oil pump.

Rick 91GT · 01-11-2001, 01:20 PM

My Canton 7qt doesn't have the provision for the oil level sensor either. I didn't modify my pan to accept it, I pulled the bulb in the dash and clipped off the wires since I never planned on running it again, all my stock one did was leak and make a mess even after replacing the seal.

------------------
My Ride Check Out My Site 91GT, Holley SysteMAX II Kit-Heads 2.02" x 1.60",Full MAC exhaust 1-5/8" Long tubes, 2-1/2" O.R H-Pipe, 2 1/2" cat back, 12" K&N Filter, RNH PERFORMANCE Ram Air, Ron Davis Radiator, Full Suspension,3:73's, Welds, Best on new motor-12.60 @ 108, no traction 1.98

MiracleMax · 01-12-2001, 12:04 AM

Ditto on the Milodon pans, I just clipped my wires and the light never came on.

01-10-2001, 05:28 PM	#1
dherrer1 Registered Member Join Date: Jul 1999 Location: Carlsbad, CA Posts: 17	Oil Pans I have a 1993 GT 5.0. I am doing a number of modifications and one is to upgrade the oil pump and oil pan. I have purchased a Moroso oil pan pant number MOR-20511 and when I received it I noticed it does not have the plug to re-install the low oil level sensor. Did I order the wrong oil pan or do I need to modify it? Has anyone crossed this bridge before? By the way, I am also installing the FMS high volume oil pump.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Aftermarket oil pans?	blue00gt	Modular Madness	2	07-19-2001 10:59 AM
67 Convertible Floor Pans	Gichigumi	Classic Mustangs	0	06-14-2001 04:12 PM
351 oil pans!	bigredstang	Windsor Power	4	05-28-2001 10:20 PM
79-82 Oil pans	zodszoo	Windsor Power	5	05-02-2001 06:29 PM
Floor pans?	86GT	Windsor Power	1	04-18-2001 09:24 PM

01-11-2001, 01:20 PM	#2
Rick 91GT Procharged! Join Date: May 1999 Location: Hanover, PA Posts: 1,539	My Canton 7qt doesn't have the provision for the oil level sensor either. I didn't modify my pan to accept it, I pulled the bulb in the dash and clipped off the wires since I never planned on running it again, all my stock one did was leak and make a mess even after replacing the seal. ------------------ My Ride Check Out My Site 91GT, Holley SysteMAX II Kit-Heads 2.02" x 1.60",Full MAC exhaust 1-5/8" Long tubes, 2-1/2" O.R H-Pipe, 2 1/2" cat back, 12" K&N Filter, RNH PERFORMANCE Ram Air, Ron Davis Radiator, Full Suspension,3:73's, Welds, Best on new motor-12.60 @ 108, no traction 1.98

01-12-2001, 12:04 AM	#3
MiracleMax Registered Member Join Date: Apr 1999 Location: Hayes, Va, USA Posts: 798	Ditto on the Milodon pans, I just clipped my wires and the light never came on.