© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
03-12-2001, 06:16 PM | #1 |
I need 110mph Trap Speed!
Join Date: Feb 1999
Location: So, CA
Posts: 4,315
|
I put my foot in my mouth...
I appologize to everyone for saying a 400hp 302 can't be built with low comrpession and all that crap.
Because today I was shocked. After dyno tuneing I made 332rwhp and 351rwtq on 87 octane with 16 deg timing with BOX Stock TFS heads, Edelbrock performer intake and E303 cam, and all accessories. This converts to 405FWHP at 18% loss. So I see 450 no problem with the drop of power steering and some higer compression. Skyler ------------------ -1989 Saleen Mustang #406-TFS Heads, E-303 Cam, Edelbrock Intake, and more. Added Eibach drag launch springs and 70/30's w/ 50/50's. 0-110MPH In car view (963k) All Throttle through 3 gears! (497k) <A HREF="http://members.aol.com/lskymanl/burnout.mpg" TARGET=_b |
03-12-2001, 06:40 PM | #2 |
Registered Member
Join Date: May 1999
Posts: 5,246
|
Whoo hoo!
Those are kick *** numbers Sky! I thought I might have been a little conservative from what I've heard about your car running! |
03-12-2001, 10:40 PM | #3 |
Procharged!
Join Date: May 1999
Location: Hanover, PA
Posts: 1,539
|
AWESOME NUMBERS SKY, CONGRAT'S
I am shooting for the 450 mark my self...I'llget it on the dyno after it's all back together and semi-tuned, Run 92 or 93 octane.my car won;t run on 87..lol Rick ------------------ My Ride Check Out My Site 91GT, Holley SysteMAX II Kit-Heads 2.02" x 1.60",Full MAC exhaust 1-5/8" Long tubes, 2-1/2" O.R H-Pipe, 2 1/2" cat back, 12" K&N Filter, RNH PERFORMANCE Ram Air, Ron Davis Radiator, Full Suspension,3:73's, Welds, Best on new motor-12.60 @ 108, no traction 1.98 |
03-12-2001, 10:50 PM | #4 |
Guest
Posts: n/a
|
I am just replying back from my thread in the Street Racers Corner.
Congrats on the dyno!!! I knew your car needed it because if mine picked up some on a stock motor, then I knew yours needed to be dialed-in. Now that I know your dyno numbers, gearing wise, I would go with 4.10's on your car. This will allow you cross about 300 rpms over your HP peak in 4th gear while using a 26" slick. About 5,800 rpms or so. This is assuming you will stay N/A. But, even if you go poweradder, just get 28" slicks to cover the extra MPH. *If you stay with 3.73's, you won't even get to your HP peak in 4th gear. You will cross the traps at about 5300 rpms. Of course, just try it out first with what you got and see how it goes. I am sure you will be happy with the results either way. If you got slicks, then get ready to get a roll bar installed, because you will surely be in the 11's with a good launch. I know a guy with a 93GT with 295rwhp that ran 11.98 @ 112 MPH, race weight of 3200 lbs, and with a good launch on BFG Drag radials. So, launch hard, drive it like you stole it, and reap the benefits. Just don't blow the rear out like me!!! My car only dynoed 298 rwhp @ 6300 rpms and 294 rwtq at 4700 rpms. My race weight is 3290 lbs. with me in the car. And look what I ran. FYI, my dyno numbers are alittle low because of my 4.56's and the entire rearend was built the day prior and due to friction from not being broken-in made my numbers show up lower than expected. But, they still aren't near yours though. Mine are actually just over 300-305 rwhp and rwtq. Keep me updated on your progress. Later, Jason ------------------ N/A 1997 Cobra 1/8 mile - 7.83 @ 90.08 MPH 1/4 mile - 12.26 @ 114.02 MPH 1.64 60 ft. |
03-12-2001, 11:27 PM | #5 |
Registered Member
Join Date: Nov 2000
Location: Maple Ridge B.C. Canada, The Best Place In The World
Posts: 871
|
WWWWOOOOOOWWWWWWW!!!!!!!!!!!!!
Are You Still Gona Build That 351? After Seein This, I Might Just Copy Your 5.0 Combo! LOL Did You Check Your Rear & See If You Had 4.10s? I Was Told Buy A Guy Who Knows The Previous Owner Of My Car That My GT Has 4.10s, But I Checked, & 2.73 Is What It Has. That Kind Of Power Is Why You Kept Up To That Race El-Camino. Later.... ------------------ 1988 Mustang GT, T-5 No Smog Pump (Shorty Belt), Dumps At The End Of Stock H-Pipe (Sounds Mean), K&N Air Filter (Stock Air Box, Removed air silendcer), 198.9 rwhp @4200 (235 Motor!!), 285 lbs-ft @2900 (336 Motor!!!). My Stang This Is What Dynomax Ultra-Flo's Do |
03-12-2001, 11:36 PM | #6 |
Registered Member
Join Date: Nov 2000
Location: Maple Ridge B.C. Canada, The Best Place In The World
Posts: 871
|
Oh ya Sky, you might want to update your users rides thing & put it in the 11/12sec range.
A pair of slicks would get you in the 11s Later... ------------------ 1988 Mustang GT, T-5 No Smog Pump (Shorty Belt), Dumps At The End Of Stock H-Pipe (Sounds Mean), K&N Air Filter (Stock Air Box, Removed air silendcer), 198.9 rwhp @4200 (235 Motor!!), 285 lbs-ft @2900 (336 Motor!!!). My Stang This Is What Dynomax Ultra-Flo's Do |
03-12-2001, 11:52 PM | #7 |
Registered Member
Join Date: Nov 1999
Location: Altoona, PA
Posts: 336
|
WAY TO GO!!! That's increadible numbers! I knew you were making some great power when I saw your burnout in 3 gears!!!! I can't wait to finish my car off now to see where I'm at myself. I called today and I guess my AFR heads are finally done- it only took since January!!! Again, congratulations on some great numbers.
------------------ 95 GT convt' 5 speed, 3.73's,FMS HD clutch, Pro 5.0 shifter, ASP alum. underdrive pulleys, Bassani offroad X pipe, 2 chmbr flowmasters, K&N w/o silencer, edelbrock performer intake, FRPP 65mm T-body, FRPP shorty headers, FRPP aluminum driveshaft.Hooker 4pt chrome car bar, Xenon/Wings West ground effects, custom interior Best ET: 13.83 Best MPH: 98.55mph with Best 60': 1.91 on Nitto DR's Homepage: <A HREF="http://www.angelfire.com/pa2/killercanary" TARGET=_blank>http://www.angelfire |
03-12-2001, 11:53 PM | #8 |
I need 110mph Trap Speed!
Join Date: Feb 1999
Location: So, CA
Posts: 4,315
|
Thanks guys! Jason- I think that I have 4.10's. Im not positive, but Im going to jack it up and find out for sure soon as I am feeling better, I'm kinda sick right now. Also my cars stock weight is 3280. Im going to put in race seats, but how did you get your car so light? I weigh 175 so 3280+175+30lb of fuel is like 3485 race weight, and my car is a fox body! If I could get to a 3200 race weight that would be awesome cuz I should trap 112+ then! I would be so stoked. I sold my ET streets and I'm going to order a set of slicks soon, cuz the 26x11.5" just wont fit anymore.
I'm gonna need a small tire. BOWTIEEATER- Im gonna stay with the 302 for now. It maybe cheaper, and with the power its making I'm quite happy with it right now! Unit- I guess thats why I beat that 383! Skyler ------------------ -1989 Saleen Mustang #406- TFS Heads, E-303, edelbrock intake,70MM TB, 73mm MAF, off road H, 2 1/4" exhaust, and 4.10's. 332RWHP@5500 351RWTQ@3750 Runs on 87 Octane! |
03-12-2001, 11:54 PM | #9 |
I need 110mph Trap Speed!
Join Date: Feb 1999
Location: So, CA
Posts: 4,315
|
Rick- What all are you changing on your engine again now? I'm anxious to see what kinda HP it will make. I heard the holley intake kicks the edelbrocks *** .
Skyler ------------------ -1989 Saleen Mustang #406- TFS Heads, E-303, edelbrock intake,70MM TB, 73mm MAF, off road H, 2 1/4" exhaust, and 4.10's. 332RWHP@5500 351RWTQ@3750 Runs on 87 Octane! |
03-13-2001, 01:40 AM | #10 |
Registered Member
Join Date: Aug 2000
Location: Thousand Oaks, CA
Posts: 396
|
Killer numbers Skyman - What HP did you start the session out with and what changes did they make to tune it? I knew you had to be higher than I was, because I've only got unported GT40P heads and I'm running cats. Especially after seeing that 3 gear burnout.
|
03-13-2001, 01:49 AM | #11 |
The Brit!
Join Date: Feb 2001
Location: Across the Pond!
Posts: 694
|
***** VERY..nICCCCCCCCEEEEEEEEE... Skyman, numbers thru the ROOF!!!!!!! tEACH ME OL MIGHTY-ONE LOL
|
03-13-2001, 08:56 AM | #12 | |
Procharged!
Join Date: May 1999
Location: Hanover, PA
Posts: 1,539
|
Quote:
I think that is about all of it , Rick ------------------ My Ride Check Out My Site 91GT, Holley SysteMAX II Kit-Heads 2.02" x 1.60",Full MAC exhaust 1-5/8" Long tubes, 2-1/2" O.R H-Pipe, 2 1/2" cat back, 12" K&N Filter, RNH PERFORMANCE Ram Air, Ron Davis Radiator, Full Suspension,3:73's, Welds, Best on new motor-12.60 @ 108, no traction 1.98 |
|
03-13-2001, 01:51 PM | #13 |
Guest
Posts: n/a
|
Awesome numbers Sky. BTW what were your 1st pull numbers like (you thought your car was in a poor state of tune). I can only hope for something that close - I am going to dyno this spring.
again congrats!! Now you need to run it. ------------------ 306ci, TFS stage 3 heads. port/pol edlebrock performer intake. 77mm mass air, 70mm TB, crane 2030 cam, Mac full length headers, flowmasters 3.73 gears and more. |
03-13-2001, 03:04 PM | #14 |
I need 110mph Trap Speed!
Join Date: Feb 1999
Location: So, CA
Posts: 4,315
|
Well first pull was 293rwhp at 5500rpm.
Sounds good rick. I really gotta lighten up my car. I got the JAZ seats too. Theyre kinda hard feeling huh? I sit down in my comfy flofit seats and I always get second thoughts about puttin them in. But I'm going to soon. I dont have the guts to pull the A/C yet. Summers soo hot here. I think the secret in the combo lies that everything is fiarly well matched, or I just got lucky. Skyler ------------------ -1989 Saleen Mustang #406- TFS Heads, E-303, edelbrock intake,70MM TB, 73mm MAF, off road H, 2 1/4" exhaust, and 4.10's. 332RWHP@5500 351RWTQ@3750 Runs on 87 Octane! |
03-13-2001, 05:10 PM | #15 |
I need 110mph Trap Speed!
Join Date: Feb 1999
Location: So, CA
Posts: 4,315
|
Hey Killer- Do you know if the saleen board is still around? I lost the link and it seemed pretty dead. Also ever hear from qkat anymore? I'd like to tell him what kinda power this made.
Skyler ------------------ -1989 Saleen Mustang #406- TFS Heads, E-303, edelbrock intake,70MM TB, 73mm MAF, off road H, 2 1/4" exhaust, and 4.10's. 332RWHP@5500 351RWTQ@3750 Runs on 87 Octane! |
03-13-2001, 11:26 PM | #16 |
Registered Member
Join Date: Nov 1999
Location: Altoona, PA
Posts: 336
|
I don't go to "THE" saleen board anymore, but I spend 90% of my time on http://talk.saleenchat.com. Its most of the regulars that frequented the "old" saleen board when it was decent. QKAT is still around, though not as much as he used to be. The link above won't work right now as the board was to be shut down for around 10 days beginning last week, but check it later this week and it should be up. Its a real nice atmosphere, kinda like "CHEERS"- everyone knows your name. There are still a good bit of technical discussions there, but nothing like here or the other boards, but the lounge there is cool. There is a big event planned by one of the regulars there coming up this 4th of July in Wash D.C.- its gonna be huge. It started out as just a few of us getting together, but now it exploded into a full on, multi-day event with numerous mustang clubs going. I'm only going on friday as it is the track night- and I'd like to gain some bragging rights , but since its only like 2-3 weeks before my wedding, I can't afford to go the entire weekend. Drop me an email if you want QKAT's email address- he probably won't believe it though- you know what I mean.
------------------ 95 GT convt' 5 speed, 3.73's,FMS HD clutch, Pro 5.0 shifter, ASP alum. underdrive pulleys, Bassani offroad X pipe, 2 chmbr flowmasters, K&N w/o silencer, edelbrock performer intake, FRPP 65mm T-body, FRPP shorty headers, FRPP aluminum driveshaft.Hooker 4pt chrome car bar, Xenon/Wings West ground effects, custom interior Best ET: 13.83 Best MPH: 98.55mph with Best 60': 1.91 on Nitto DR's Homepage: <A HREF="http://www.angelfire.com/pa2/killercanary" TARGET=_blank>http://www.angelfire |
03-14-2001, 05:10 PM | #17 |
Registered Member
Join Date: Mar 2001
Location: San Diego, CA, USA
Posts: 86
|
Skyman, could you do me a favor and check to see if you really have those 4:10 gears?
I have been thinking about doing a gear swap next month for my 87GT T-5. I'm just a little worried that i might go too much with the 4:10's. thanks |
03-14-2001, 05:21 PM | #18 |
I need 110mph Trap Speed!
Join Date: Feb 1999
Location: So, CA
Posts: 4,315
|
I'm checking as soon as I'm over being sick and get out of infront of this monitor . Should be tomorrow or so.
Skyler ------------------ -1989 Saleen Mustang #406- TFS Heads, E-303, edelbrock intake,70MM TB, 73mm MAF, off road H, 2 1/4" exhaust, and 4.10's. 332RWHP@5500 351RWTQ@3750 Runs on 87 Octane! |
03-14-2001, 05:47 PM | #19 |
Registered Member
Join Date: Feb 2001
Location: Berkshire County - Massachusetts
Posts: 735
|
Cngrats!!
Tear dem Chevy's a new $#%hole Now I know that 450+ HP is possible with my in-progress combo below! ------------------ In-progress Street Legal 351..(So far)Edlebrock Performer RPM head, Upper&Lower Manifold..Crane Gold 1.6 Rollers..BBK 70MM TB..Full Cartech Fuel System..30lb Injectors.. Sothside Machine bars&sub-frames..Air Bag rear end..3.73's..???Tranny |
03-14-2001, 10:58 PM | #20 |
Registered Member
Join Date: Mar 2001
Location: Morganton, NC, USA
Posts: 6
|
I noticed the guys at Corral bashing your numbers. Those are good numbers in my book! Some people know it all! They would have a field day with my '88 coupe. Out of the box windsor JRs, ported stock lower, comp box upper, Lunati cam (490 lift), long tubes, 2.5 exhaust. 12.6 @ 108, Bristol FFW True Street 2000.
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Anyone heard the SLP loud mouth exhaust. | 91redgt | Modular Madness | 3 | 12-03-2003 08:10 AM |
Boy, Vortech's sure do leave a bad taste in your mouth when you eat them!! | Eric4Nitrous | Blue Oval Lounge | 21 | 05-22-2002 07:59 AM |
Which foot when braking with auto? | lx mike | Blue Oval Lounge | 15 | 12-02-2001 09:42 AM |
Everyones 60 foot times... | jz_mustang50 | Windsor Power | 15 | 10-10-2001 08:41 AM |
20 foot burn out in a ford taurus | Chevysucks | Windsor Power | 13 | 03-06-2001 04:15 PM |